Comtech EF Data SNM-1002 User Manual
Page 141
SNM-1002 LinkSync
Modem
Revision 2
Remote Control Operation
MN/SNM1002.OM
A–15
Demodulat
or Config.
Status
Command:
Response:
DF_nnn.nnnnnn'cr'
DR_nnnn_mmmm.mmm'cr'
ADRA_nnnn_mmmm.mmm'cr'
ADRB_nnnn_mmmm.mmm'cr'
ADRC_nnnn_mmmm.mmm'cr'
ADRD_nnnn_mmmm.mmm'cr'
ADRV_nnnn_mmmm.mmm'cr'
DE_xxx'cr'
DDEC_xxx'cr'
RFL_xxx'cr'
IFL_xxx'cr'
SCF_snnnnn'cr'
SWR_nnnnn'cr'
SR_xxx'cr'
BERT_xxxx'cr'
DT_xxxx'cr'
DDT_xxx'cr'
DSR_xxx'cr'
RSDE_xxx'cr'
RDA_xxx'cr'
RRSI_xx'cr'
R310_xxx'cr''lf']
Demodulator Frequency
Demodulator Rate
Preset 'A' Assignment
Preset 'B' Assignment
Preset 'C' Assignment
Preset 'D' Assignment
Preset 'V' Assignment
Descrambler Enable
Differential Decoder
RF Loopback
IF Loopback
Sweep Center Frequency
Sweep Width Range
Sweep Reacquisition
BER Threshold
Demodulator Type
Demodulator Decoder Type
Demodulator Spectrum Rotation
Reed-Solomon Decoder
Receive BPSK Data Ordering
RX Reed-Solomon Interleave Value
RX 8PSK 2/3 IESS-310 Operation
The demodulator configuration status command
causes a block of data to be returned by the
addressed modem. The block of data reflects the
current configuration of the demod. Additional
configuration status of new options and features
will always be appended to the end.
Demod/
Decoder
Config.
Program
Status
Command:
Response:
SMT_xxxxxxx'cr'
IROT_xxxxx'cr'
MOM_xxxxxxx'cr'
BERT_xxxx'cr'
DT_xxxx'cr'
DDT_xxx'cr'
RCEN_1_xxxx'cr' (Note 1)
RCDR_1_xxxx.x'cr' (Note 2)
RCEN_2_xxx'cr'
(Note 1)
RCEN_3_xxxx'cr' (Note 1)
RCDR_3_xxxx.x'cr' (Note 3)
RCCP_3_yyy'cr' (Note
3)
RCDP_3_yyy'cr' (Note
3)
RCEN_4_xxxx'cr' (Note 1)
RCDR_4_xxxx.x'cr' (Note 4)
RCCP_4_yyy'cr' (Note
4)
RCDP_4_yyy'cr' (Note
4)
DF_nnn.nnnnnn'cr'
DR_nnnn_mmmm.mmm'cr'
DE_xxx'cr'
DDEC_xxx'cr'
RFL_xxx'cr'
IFL_xxx'cr'
SCF_snnnnn'cr'
SWR_nnnnn'cr'
SR_xxx'cr'
System Modem Type
Interface Receive Overhead Type
Modem Operation Mode
BER Threshold
Demodulator Type
Demodulator Decoder Type
Flex Mux RX Channel #1 Enable
Flex Mux RX Channel #1 Data Rate
Flex Mux RX Channel #2 Enable
Flex Mux RX Channel #3 Enable
Flex Mux RX Channel #3 Data Rate
Flex Mux RX Channel #3 Clock Phase
Flex Mux RX Channel #3 Data Phase
Flex Mux RX Channel #4 Enable
Flex Mux RX Channel #4 Data Rate
Flex Mux RX Channel #4 Clock Phase
Flex Mux RX Channel #4 Data Phase
Demodulator Frequency
Demodulator Rate
Descrambler Enable
Differential Decoder
RF Loopback
IF Loopback
Sweep Center Frequency
Sweep Width Range