BECKHOFF EP9214-0023 - Manual (Page 93)

Comissioning and Configuration
4.6.2.2.32 Index 1C32 SM output parameter
Index Name Meaning Data type Flags Default
1C32:0 SM output
parameter Synchronization parameters for the outputs UINT8 RO 0x20 (32
dec
)
1C32:01 Sync mode Current synchronization mode:
• 0: Free Run
• 1: Synchronous with SM 2 event
• 2: DC-Mode - Synchronous with SYNC0
Event
• 3: DC-Mode - Synchronous with SYNC1 event
UINT16 RW 0x0000 (0
dec
)
1C32:02 Cycle time Cycle time (in ns):
• Free Run: Cycle time of the local timer
• Synchronous with SM 2 event: Master cycle
time
• DC-Mode: SYNC0/SYNC1 Cycle Time
UINT32 RW 0x000F4240 (1000000
dec
)
1C32:03 Shift time Time between SYNC0 event and output of the out-
puts (in ns, DC mode only) UINT32 RO 0x00000384 (900
dec
)
1C32:04 Sync modes
supported Supported synchronization modes:
• Bit 0 = 1: free run is supported
• Bit 1 = 1: Synchronous with SM 2 event is
supported
• Bit 2-3 = 01: DC mode is supported
• Bit 4-5 = 10: Output shift with SYNC1 event
(only DC mode)
• Bit 14 = 1: dynamic times (measurement
through writing of 1C32:08)
UINT16 RO 0x0001 (1
dec
)
1C32:05 Minimum
cycle time Minimum cycle time (in ns) UINT32 RO 0x000F4240 (1000000
dec
)
1C32:06 Calc and
copy time Minimum time between SYNC0 and SYNC1 event (in
ns, DC mode only) UINT32 RO 0x00000000 (0
dec
)
1C32:07 Minimum
delay time UINT32 RO 0x00000384 (900
dec
)
1C32:08 Command • 0: Measurement of the local cycle time is
stopped
• 1: Measurement of the local cycle time is
started
The entries 1C32:03, 1C32:05, 1C32:06, 1C32:09,
1C33:03, 1C33:06, and 1C33:09 are updated with the
maximum measured values.
For a subsequent measurement the measured values
are reset
UINT16 RW 0x0000 (0
dec
)
1C32:09 Maximum
delay time Time between SYNC1 event and output of the out-
puts (in ns, DC mode only) UINT32 RO 0x00000384 (900
dec
)
1C32:0B SM event
missed
counter Number of missed SM events in OPERATIONAL (DC
mode only) UINT16 RO 0x0000 (0
dec
)
1C32:0C Cycle ex-
ceeded
counter Number of occasions the cycle time was exceeded in
OPERATIONAL (cycle was not completed in time or
the next cycle began too early) UINT16 RO 0x0000 (0
dec
)
1C32:0D Shift too
short
counter Number of occasions that the interval between
SYNC0 and SYNC1 event was too short (DC mode
only) UINT16 RO 0x0000 (0
dec
)
1C32:20 Sync error The synchronization was not correct in the last cycle,
(outputs were output too late; DC mode only) boolean RO 0x00 (0
dec
)
EP9214-0023 and EP9224-0023 93 Version 2.0.0