Diode LED RGB Zone Control - Manual (Page 2)

1.877.817.6028
www.DiodeLED.com
[email protected] www.DiodeLED.com
INSTALLATION GUIDE
2 OF 4
RGB ZONE COLOR CONTROLLER
®
Operation
Mount RGB Receiver to Surface. See ‘Wiring Connections’, use
applicable screws.
Attach Lighting Load and Driver. Only use copper wiring.
Reference ‘Wiring Connections’ located further in guide for
visual. Use a mini flathead screwdriver for attaching wires to
terminal ports. Terminals fit up to 12AWG solid-core copper
wire. Verify a compatible constant voltage driver is installed.
Install Additional Components, Verify Connections, and Turn
Main Power ON at Breaker.
3
4
5
ON OFF
OFF
OFF
ON
ON
OFF
OFF
ON
ON
If system remains unresponsive
or is working improperly, turn OFF
main power at breaker and verify
all connections. Review the ‘Wiring
Connections’ or ‘Troubleshooting’
sections for further details.
Charging the Zone Remote
• A flashing red indicator light on the Zone Remote implies a low battery.
• To charge the Zone Remote, connect the included USB 2.0A/Mini-B cable to the remote and to any USB compatible computer or mobile charger
with a USB port (not included).
• Press the power button on the Zone Remote and a blue indicator light will flash continuously to indicate charging. Once the indicator light turns
green, charging is complete.
Resetting Receiver to Factory Settings
• To reset a single receiver, long press the ‘Power’ button on the receiver (you will hear an initial beep). Continue holding for >8 seconds until the
receiver long beeps. The receiver has now been reset to factory settings.
Pairing the Zone Remote with a Zone Receiver. The Zone
Remote can control up to 10 different Zone Receivers. Only one
remote can be paired to each receiver. To pair the Zone Remote
with a Zone Receiver:
• POWER: Turns the Zone Receiver and Zone Remote ON/OFF.
• PAUSE: A quick press of the PAUSE key freezes the current MODE. Holding the PAUSE key on the Zone Remote for 3 seconds will turn the sound
on all Zone Receivers ON/OFF.
• MODE: Cycles through 18 pre-programmed MODES. Holding MODE for 3 seconds until a long beep sounds will cycle the MODE to No. 1 of the
Mode Description Chart and adjust the SPEED to 5.
• SPEED: Press to cycle through 8 different SPEEDS of any current MODE. Holding SPEED for 3 seconds until a buzzer sounds will adjust the SPEED
to 5.
• BRIGHTNESS: Press to cycle through 8 BRIGHTNESS levels of any current MODE or single color. Holding BRIGHTNESS will gradually increase light
intensity. A quick double-beep indicates maximum brightness if sound is turned on (see PAUSE key for turning sound ON/OFF).
• COLOR ADJUSTMENT WHEEL: Adjusts static colors. The LED indicator in the center of the COLOR ADJUSTMENT WHEEL displays the current static
color selected.
• ZONE CONTROL: Selects a specific zone to control (1-10). To choose all 10 zones press “ * ” twice. To control a selected number of zones in sync
press “ * + any numeral + * ”. For example, if you would like to control zones 1, 5, & 9 together, press “ * 159 * ”.
• SAVED SCENE: Holding M1 or M2 (Memory 1 or Memory 2) for 3 seconds will save the current static color or MODE to a SAVED SCENE. To indicate
a saved scene the zone receiver will long beep and a red indicator light will flash 3 times on the Zone Remote.
6
1. Turn on the Remote and Receiver by pressing the power button on
each device.
2. Next, press and hold the power button on the Receiver for 3 seconds
until you hear a short beep, and continue to hold. Once the Receiver
short beeps immediately hold down a zone number of your choice
(1-10) on the Remote. Ensure to continue holding the power button on
the Receiver after it beeps, and then simultaneously choose a zone on
the Remote.
3. To indicate pairing, the Receiver will long beep and a green indicator
light will flash 3 times on the Remote.
See the online product page for video
tutorials or contact technical support.
Need Additional Assistance?
IG060914-1.2