Rockwell Automation 1771-QDC, D17716.5.85(Passport) MNL. PLASTIC MOLDING MODULE - Manual (Page 184)

Enter Your Values Here
Blank Worksheets
Appendix A
A-15
Worksheet 7ĆD (continued)
Plastication Configuration Block (PLC)
Control Word ProĆSet 600 Addr. Value Description Units
PLC05 N44:361 1000 Minimum RPM Control ERC Percentage Percent 8
PLC06 N44:362 1000 Minimum Pressure Control ERC Percentage Percent 8
PLC08 N44:364 0 Profile Watchdog Timer Preset Time 1
PLC09 N44:365 * Output #1 SetĆoutput Value During Profile Percent Signal Output 4
PLC10 N44:366 * Output #2 SetĆoutput Value During Profile Percent Signal Output 4
PLC11 N44:367 * Output #3 SetĆoutput Value During Profile Percent Signal Output 4
PLC12 N44:368 * Output #4 SetĆoutput Value During Profile Percent Signal Output 4
PLC17 N44:373 0 Output #1 Acceleration Ramp Rate During Profile Percent Signal Output per Second 5
PLC18 N44:374 0 Output #2 Acceleration Ramp Rate During Profile Percent Signal Output per Second 5
PLC19 N44:375 0 Output #3 Acceleration Ramp Rate During Profile Percent Signal Output per Second 5
PLC20 N44:376 0 Output #4 Acceleration Ramp Rate During Profile Percent Signal Output per Second 5
PLC25 N44:381 0 Output #1 Deceleration Ramp Rate During Profile Percent Signal Output per Second 5
PLC26 N44:382 0 Output #2 Deceleration Ramp Rate During Profile Percent Signal Output per Second 5
PLC27 N44:383 0 Output #3 Deceleration Ramp Rate During Profile Percent Signal Output per Second 5
PLC28 N44:384 0 Output #4 Deceleration Ramp Rate During Profile Percent Signal Output per Second 5
PLC33 N44:389 * Output #1 SetĆoutput Value at EndĆof Profile Percent Signal Output 4
PLC34 N44:390 * Output #2 SetĆoutput Value at EndĆof Profile Percent Signal Output 4
PLC35 N44:391 * Output #3 SetĆoutput Value at EndĆof Profile Percent Signal Output 4
PLC36 N44:392 * Output #4 SetĆoutput Value at EndĆof Profile Percent Signal Output 4
PLC41 N44:397 0 Pressure Minimum Control Limit Pressure 3
PLC42 N44:398 * Pressure Maximum Control Limit Pressure 3
PLC43 N44:399 * Selected Pressure Valve, Output for Minimum Percent Signal Output 4
PLC44 N44:400 * Selected Pressure Valve, Output for Maximum Percent Signal Output 4
PLC45 N44:401 0 RPM Minimum Control Limit RPM 2
PLC46 N44:402 * RPM Maximum Control Limit RPM 2
PLC47 N44:403 * Selected RPM Valve, Output for Minimum Percent Signal Output 4
PLC48 N44:404 * Selected RPM Valve, Output for Maximum Percent Signal Output 4
PLC49 N44:405 100 Proportional Gain for Pressure Control None
PLC50 N44:406 400 Integral Gain for Pressure Control Inverse Time (Algorithm) 6
PLC51 N44:407 0 Derivative Gain for Pressure Control Time (Algorithm) 7
PLC52 N44:405 100 Proportional Gain for RPM Control None
PLC53 N44:406 400 Integral Gain for RPM Control Inverse Time (Algorithm) 6
PLC54 N44:407 0 Derivative Gain for RPM Control Time (Algorithm) 7
PLC57 N44:413 0 Profile High Pressure Alarm Setpoint Pressure 3
1 Time 2 Screw Speed 3 Pressure 4 Percent Signal Output
00.00 to 99.99 seconds 000.0 to 999.9 RPM 0000 to 9999 PSI 00.00 to 99.99
000.0 to 999.9 Bar
5 Percent Signal Output per Second 6 Inverse Time (Algorithm) 7 Time (Algorithm) 8 Percent
0000 to 9999 00.00 to 99.99 Minutes (ISA) 00.00 to 99.99 Minutes (ISA) 00.00 to 99.99
00.00 to 99.99 Seconds (AĆB) 00.00 to 99.99 Seconds (AĆB)
* Refer to the appropriate section later in this chapter for information on this parameter