Rockwell Automation 1560E SMC Flex Smart Motor Controller - Manual (Page 74)

3-6 Commissioning Procedures
1560E-UM050B-EN-P - June 2013
SW2: When ON (up) provides
test pulses to gate driver circuits.
NOTE: Must be OFF (down) for
normal operation.
LED (Red): ON when
test pulses on.
SMC-Flex control module
Ribbon connectors to connect
to SMC-Flex control module
(underneath control module)
TP1,2,3,5,7,9:
Voltage feedback
test points
TB21: Ribbon
connector to Voltage
Sensing Board
TB5:
Current
transformer
connections
LED (Green):
ON when power
is present
TP18,19,20:
Power supply
test points
Replacement
Part Number
Serial Number L N G
Control Power
110-240 VAC or
110-250 VDC
SW3: Used to
defeat temperature
feedback channels
Temperature
Feedback
Fibre Optic
Receivers
Phase C
Fibre Optic
Transmitters
Phase B
Fibre Optic
Transmitters
Phase A
Fibre Optic
Transmitters
send gate
signals to
driver boards
LED (Yellow) ON
when Phase A
gate signal active
TP4: Phase A
gate signal
TP8: Common for
Gate/Pulse TPs
LED (Yellow) ON
when Phase B
gate signal active
TP11: Phase B
gate signal
LED (Yellow): ON
when Phase C
gate signal active
TP13: Phase C
gate signal
TP15: Common for
Gate/Pulse TPs
LEDs (Green): ON when signal
present at temperature feedback
fibre optic receivers
Phase A
Phase B
Phase C
TB6: Gate driver
power supply input
SW2: When ON (up) provides
test pulses to gate driver circuits.
NOTE: Must be OFF (down) for
normal operation.
LED (Red): ON when
test pulses on.
SMC-Flex control module
Ribbon connectors to connect
to SMC-Flex control module
(underneath control module)
TP1,2,3,5,7,9:
Voltage feedback
test points
TB21: Ribbon
connector to Voltage
Sensing Board
TB5:
Current
transformer
connections
LED (Green):
ON when power
is present
TP18,19,20:
Power supply
test points
Replacement
Part Number
Serial Number L N G
Control Power
110-240 VAC or
110-250 VDC
SW3: Used to
defeat temperature
feedback channels
Temperature
Feedback
Fibre Optic
Receivers
Phase C
Fibre Optic
Transmitters
Phase B
Fibre Optic
Transmitters
Phase A
Fibre Optic
Transmitters
send gate
signals to
driver boards
LED (Yellow) ON
when Phase A
gate signal active
TP4: Phase A
gate signal
TP8: Common for
Gate/Pulse TPs
LED (Yellow) ON
when Phase B
gate signal active
TP11: Phase B
gate signal
LED (Yellow): ON
when Phase C
gate signal active
TP13: Phase C
gate signal
TP15: Common for
Gate/Pulse TPs
LEDs (Green): ON when signal
present at temperature feedback
fibre optic receivers
Phase A
Phase B
Phase C
TB6: Gate driver
power supply input
SW2: When ON (up) provides
test pulses to gate driver circuits.
NOTE: Must be OFF (down) for
normal operation.
LED (Red): ON when
test pulses on.
SMC-Flex control module
Ribbon connectors to connect
to SMC-Flex control module
(underneath control module)
TP1,2,3,5,7,9:
Voltage feedback
test points
TB21: Ribbon
connector to Voltage
Sensing Board
TB5:
Current
transformer
connections
LED (Green):
ON when power
is present
TP18,19,20:
Power supply
test points
Replacement
Part Number
Serial Number L N G
Control Power
110-240 VAC or
110-250 VDC
SW3: Used to
defeat temperature
feedback channels
Temperature
Feedback
Fibre Optic
Receivers
Phase C
Fibre Optic
Transmitters
Phase B
Fibre Optic
Transmitters
Phase A
Fibre Optic
Transmitters
send gate
signals to
driver boards
LED (Yellow) ON
when Phase A
gate signal active
TP4: Phase A
gate signal
TP8: Common for
Gate/Pulse TPs
LED (Yellow) ON
when Phase B
gate signal active
TP11: Phase B
gate signal
LED (Yellow): ON
when Phase C
gate signal active
TP13: Phase C
gate signal
TP15: Common for
Gate/Pulse TPs
LEDs (Green): ON when signal
present at temperature feedback
fibre optic receivers
Phase A
Phase B
Phase C
TB6: Gate driver
power supply input
Figure 3.2 – Connection and Test Information for Interface Board