Red Lion PAX2D - Manual (Page 23)

23
LINE 2 DISPLAY SCROLL ENABLE/TIME
NO 1 to 15 seconds
If Line 2 Display Scrolling is desired, set the scroll time in seconds.
LINE 2 UNITS MNEMONIC(S)
OFF CUSt Lb-CSt Lb Ln1
LAbEL FACt Lb-FAC L1-FAC
Select the mode for Line 2 Units Mnemonic(s). See LINE 2 UNITS
MNEMONIC DIAGRAM for programming details.
SELECTION MODE DESCRIPTION
OFF OFF No Line 2 mnemonics shown.
LAbEL LABEL Single programmable mnemonic shown as a
separate item in the Line 2 Display loop. No
individual mnemonics are shown with the other
Line 2 Display values.
CUSt CUSTOM Individual Custom programmable mnemonics
shown with each value in the Line 2 Display loop.
FACt FACTORY Individual Factory default mnemonics shown with
each value in the Line 2 Display loop.
Lb-CSt LABEL &
CUSTOM
A programmable mnemonic shown as a separate
item in the Line 2 Display loop. Also, individual
Custom programmable mnemonics shown with
each value in the Line 2 Display loop.
Lb-FAC LABEL &
FACTORY
A programmable mnemonic shown as a separate
item in the Line 2 Display loop. Also, individual
Factory default mnemonics shown with each
value in the Line 2 Display loop.
Lb Ln1 LINE 1
INDEXED
LABELS
Individual programmable mnemonics, indexed to
the Line 1 Display value, are shown as a
separate item in the Line 2 Display loop. These
same mnemonics are also shown with each
value in the Line 2 Display loop.
L1-FAC LINE 1
INDEXED
LABELS &
FACTORY
Individual programmable mnemonics, indexed to
the Line 1 Display value, are shown as a
separate item in the Line 2 Display loop. Also,
individual Factory default mnemonics are shown
with each value in the Line 2 Display loop.
The characters available for the programmable modes include:
A b C d E F G H I J k L M N O P q r S t U W Y Z 0 1
2 3 4 5 6 7 8 9 a c e g h i
m n o u w
- = [ ] / ° _ blank
PROGRAMMING SECURITY CODE
0 to 250
To activate either the Parameter or Hidden Parameter display loops, a security
code (1-250) must be entered. If a “0” security code is programmed, pressing the
P key takes you directly to the Full Programming Mode.
The Security Code determines the programming mode and the accessibility
of programming parameters. This code can be used along with the Program
Mode Lock-out (PLOC) in the User Input Function parameter (Input [User]
module).
Two programming modes are available. Full Programming Mode allows all
parameters to be viewed and modified. Parameter display loop mode provides
access to those selected parameters, that can be viewed and/or modified without
entering the Full programming mode.
The following chart indicates the levels of access based on various CodE and
User Input PLOC settings.
SECURITY
CODE
USER INPUT
CONFIGURED
USER INPUT
STATE
WHEN P KEY IS
PRESSED
FULL PROGRAMMING
MODE ACCESS
0 not PLOC ———— Full Programming Immediate Access
0 PLOC Not Active Full Programming Immediate Access
0 PLOC Active
Enter Parameter
Display Loop
No Access
>0 not PLOC ———— Enter Parameter
Display Loop
After Parameter
Display Loop with
correct code # at
COdE prompt.
>0 PLOC Not Active Full Programming Immediate Access
>0 PLOC Active
Enter Parameter
Display Loop
After Parameter
Display Loop with
correct code # at
COdE prompt.
ScroLL
NO
Ln2
UNItS
FACt
Ln2
Two character spaces are required to display this character.
COdE
0
Ln2
P
LINE 2 UNITS MNEMONIC DIAGRAM (9-DIGITS)
Edit
NO
P Edit CSt
NO
P UNItS Ln2
OFF
COdE Ln2
000
UNItS Ln2
LAbEL
Edit
YES
UNItS Ln2
CUSt
Edit
Cnt A
Unit 1
1
Unit 2
2
Unit 9
9
Edit
Cnt b
Edit
Lo
P P P P
Unit 1
1
Unit 2
2
Unit 9
9
P P P P
P
P
Unit 1
1
Unit 2
2
Unit 9
9
P P P P
Unit 1
1
Unit 2
2
Unit 9
9
P P P P
Lb
Lb Lb Lb Lb
CSt
CSt
CSt
CtA CtA CtA
Ctb Ctb Ctb
Lo Lo Lo
(Unit 3 thru 8)
(Unit 3 thru 8)
(Unit 3 thru 8)
(Unit 3 thru 8)
(returns to currently selected value)
P UNItS Ln2
FACt
Lb-CSt
Lb-CSt
Lb-FAC
Lb Ln1
L1-FAC
Additional Display Values:
(Count C, Rate A, Rate B, Rate C, Hi)
F1 F2
F1 F2
F1 F2