Red Lion PAX2D - Manual (Page 17)

17
OUtPUt
SEtPNt
SELECt
S1
SPt
Setpoint
Select
ASSIGN
NONE
S n
Setpoint
Assignment
LOGIC
NOr
S n
Output
Logic
ACtION
NO
S n
Setpoint
Action
Annun
NOr
S n
Setpoint
Annunciator
Color
NO CHG
S n
Line 1 Change
Color
SEtPNt
100
S n
Setpoint
Value
trAC
NO
S n
Setpoint
Tracking
tYPE
HI-ACt
S n
Activation
Type
P-UP
OFF
S n
Output Power-up
State
n = Setpoint Number (1-4)
StbY
NO
S n
Setpoint
Standby
Operation
t-ON
0.00
S n
Off Time
Delay
HYSt
0
S n
Hysteresis
Value
t-OFF
0.00
S n
On Time
Delay
t-OUt
1.00
S n
Output
Time-out
Value
1-SHOt
NO
S n
Rate Timed
Output One-Shot
Mode
AUtO
NO
S n
Counter
Auto Reset
RESEt
NO
S n
Output Reset
With Counter
Reset
RSt-Sn
NO
S n
Output Reset
at Sn+1
Pro
OUtPUt
Pro
NO
F1 F2
P
D
O
uTpuT
p
arameTers
(OUtPUt)
SETPOINT OUTPUT PARAMETERS (SEtPNt)
This section details the programming for the setpoints. To have output capabilities, a setpoint Plug-in card needs to be installed into the PAX2D (see Ordering
Information). Depending on the card installed, there will be two or four setpoint outputs available. If no output card is installed, programming for the setpoints is still
available. An Exchange Parameter Lists feature for setpoint values is explained in User Input programming. For maximum input frequency, unused setpoints should
be configured for NO action.
The Setpoint Assignment and Setpoint Output Action determine setpoint feature availability. The Setpoint Parameter Availability chart illustrates this.
SETPOINT DEACTIVATE (RESET) MOMENTARY (EDGE)
When activated (momentary action), the meter deactivates (resets) the
setpoint outputs configured as YES in the sublist.
DISPLAY DESCRIPTION FACTORY
S1 Setpoint 1 NO
S2 Setpoint 2 NO
S3 Setpoint 3 NO
S4 Setpoint 4 NO
SETPOINT ACTIVATE (SET) MAINTAINED (LEVEL)
The meter activates (sets) the setpoint outputs configured as YES in the
sublist, as long as activated (maintained action).
DISPLAY DESCRIPTION FACTORY
S1 Setpoint 1 NO
S2 Setpoint 2 NO
S3 Setpoint 3 NO
S4 Setpoint 4 NO
SETPOINT ACTIVATE (SET) MOMENTARY (EDGE)
When activated (momentary action), the meter activates (sets) the setpoint
outputs configured as YES in the sublist.
DISPLAY DESCRIPTION FACTORY
S1 Setpoint 1 NO
S2 Setpoint 2 NO
S3 Setpoint 3 NO
S4 Setpoint 4 NO
HOLD SETPOINT STATE
The meter holds the state of the setpoint outputs configured as YES in the
sublist, as long as activated (maintained action).
DISPLAY DESCRIPTION FACTORY
S1 Setpoint 1 NO
S2 Setpoint 2 NO
S3 Setpoint 3 NO
S4 Setpoint 4 NO
USEr-n
SPr-E
USr Fn
SPr-E
FNC
USEr-n
SPS-L
USr Fn
SPS-L
FNC
USEr-n
SPS-E
USr Fn
SPS-E
FNC
USEr-n
SPHOLd
USr Fn
SPHOLd
FNC
OUTPUT SELECT
SEtPNt ANALOG
Select the Setpoint or Analog output to be programmed. The Analog output selection
only appears if an analog output plug-in card is installed in the meter.
OUtPUt
SEtPNt
SETPOINT PARAMETER AVAILABILITY
PARAMETER DESCRIPTION
COUNTER ASSIGNMENT RATE ASSIGNMENT
TIMED OUT
t-OUt
BOUNDARY
bOUNd
LATCH
LAtCH
TIMED OUT
t-OUt
BOUNDARY
bOUNd
LATCH
LAtCH
LOGIC Setpoint Output Logic Yes Yes Yes Yes Yes Yes
Annun Setpoint Annunciator Yes Yes Yes Yes Yes Yes
Color Setpoint Line 1 Color Yes Yes Yes Yes Yes Yes
SEtPNt Setpoint Value Yes Yes Yes Yes Yes Yes
trAC Setpoint Tracking Yes Yes Yes Yes Yes Yes
P-UP Setpoint Output Power-up State No No Yes No No Yes
tYPE Setpoint Activation Type No Yes No Yes Yes Yes
StbY Standby Operation No Yes No Yes Yes Yes
HYSt Setpoint Hysteresis No No No Yes Yes No
t-ON Setpoint On Time Delay No No No Yes Yes Yes
t-OFF Setpoint Off Time Delay No No No No Yes No
t-OUt Setpoint Output Time-out Value Yes No No Yes No No
1-SHOt Rate Timed Output One-shot No No No Yes No No
AUtO Counter Auto Reset Yes No Yes No No No
RESEt Output Reset with Manual Reset Yes No Yes No No No
RSt-Sn Setpoint Output Reset at Sn+1 Yes No Yes No No No