Yokogawa IR400 User Manual
User's manual, Ir400 infrared gas analyzer
Table of contents
Document Outline
- IR400
- PREFACE
- CAUTION ON SAFETY
- After Sales Warranty
- CONTENTS
- 1. OVERVIEW
- 2. NAME AND DESCRIPTION OF EACH UNIT
- 2.1 Nane and description of main unit
- 2.2 Input/Output terminal module
- 3. INSTALLATION
- 3.1 Installation conditions
- 3.2 Installation
- 3.2.1 Installation of analyzer main frame
- 3.2.2 Mounting input/output terminal module
- 3.3 Piping
- 3.4 Sampling
- 3.4.1 Conditions of sampling gas
- 3.4.2 Sampling gas flow
- 3.4.3 Preparation of standaed gas
- 3.4.4 Reduction of moisture interference
- 3.4.5 Purging of instrument inside
- 3.4.6 Pressure at sampling gas outlet
- 3.4.7 Example configuration of gas sampling system
- 3.5 Wiring
- 3.5.1 Power inlet
- 3.5.2 Input/output terminal module
- 4. OPERATION
- 4.1 Preparation for operation
- 4.2 Wram-up operation and regular operation
- 5. DESCRIPTION OF DISPLAY AND OPERATION PANELS
- 5.1 Name and description of operation panel
- 5.2 Overview of display and operation panels
- 5.3 Outline of display screen
- 5.4 Genenal operation
- 6. SETTING AND CALIBRATION
- 6.1 Switch of range
- 6.1.1 Setting of range switch mode
- 6.1.2 Manual range switch
- 6.2 Calibration setting
- 6.2.1 Setting of calibration concentration
- 6.2.2 Setting of manual zero calibration
- 6.2.3 Setting of calibration range
- 6.2.4 Setting of auto calibration component/range
- 6.3 Alarm setting
- 6.3.1 Setting of alarm values
- 6.3.2 Hysteresis setting
- 6.4 Setting of auto calibration
- 6.4.1 Auto calibration
- 6.4.2 Forced run/stop of calibration
- 6.4.2.1 Execution of auto calibration*only once(
- 64.2.2 Forced stop of auto calibration
- 6.5 Setting of auto zero calibration
- 6.5.1 Autozero calibration
- 6.5.2 Forced run/stop of auto zero calibration
- 6.5.2.1 Execution of auto zero calibration *just once(
- 6.5.2.2 Forced stop of auto zero calibration
- 6.6 Peak alarm setting
- 6.7 Parameter setting
- 6.8 maintenance mode
- 6.9 Calibration
- 6.9.1 Zero calibration
- 6.9.2 Span calibration
- 7.MAINTENANCE
- 7.1 Daily check
- 7.2Daily check and maintenance procedures
- 7.3 Maintenance of analyzer unit
- 7.3.1 Cleaning method for sample cell *pipe cell(
- 7.3.2 Cleaning method for sample cell (block cell)
- 7.3.3 Optical zero adjustment method (optical balance adjustment)
- 7.3.4 Moisture interference compensation adjustment method
- 7.3.5 Replacement of fuse on analyzer unit
- 7.4 Inspection and maintenance of limited service-life components
- 8. TROUBLE SHOOTING FOR ANALYZER
- 8.1 Error message
- 8.2 Troubleshooting
- 9. SPECIFICATIONS
- 9.1 Genenal specifications
- 9.2 Model and Suffix codes
- 9.3 External Dimensions
- CMPL
- Revision Record