Yamaha EX5R - Manual (Page 172)

Per
for
mance Mode
172
Lyr 1:Pf 2:Pf 3:Pf 14:Pf 15:Pf 16:Pf
Bank P1 P1 P1 P1 P1 P1
Number 001 001 001 001 001 001
Volume 100 100 100 100 100 100 100
Pan cnt cnt cnt cnt cnt cnt cnt
Rev Send 40 40 40 40 40 40 40
Cho Send 0 0 0 0 0 0 0
InsEF Sw off off off off off off
Out Sel L&R L&R L&R L&R L&R L&R
Detune +0 +0 +0 +0 +0 +0 +0
MonoPoly poly poly poly poly poly poly poly
KeyAsign mlti mlti mlti mlti mlti mlti
MDPanVol off off off off off off
Layer Sw on on on on on on
Nt Lmt L C-2 C-2 C-2 C-2 C-2 C-2
Nt Lmt H G8 G8 G8 G8 G8 G8
VelLmt L 1 1 1 1 1 1
VelLmt H 127 127 127 127 127 127
NoteShft +0 +0 +0 +0 +0 +0
Vel Sens 64 64 64 64 64 64
Vel Crve norm norm norm norm norm norm
Vel Ofst +0 +0 +0 +0 +0 +0
Arpeggio on on on on on on
Tx MIDIA on on on on on on
Tx MIDIB on on on on on on
MIDItoTG on on on on on on
MIDI Ch 1 2 3 14 15 16
Bright +0 +0 +0 +0 +0 +0 +0
Harmonic +0 +0 +0 +0 +0 +0 +0
Attack +0 +0 +0 +0 +0 +0 +0
Decay +0 +0 +0 +0 +0 +0 +0
Release +0 +0 +0 +0 +0 +0 +0
Vib Rate +0 +0 +0 +0 +0 +0 +0
VibDelay +0 +0 +0 +0 +0 +0 +0
VibDepth +0 +0 +0 +0 +0 +0 +0
PEG Init +0 +0 +0 +0 +0 +0 +0
PEG Atck +0 +0 +0 +0 +0 +0 +0
PEG RelL +0 +0 +0 +0 +0 +0 +0
PEG RelT +0 +0 +0 +0 +0 +0 +0
PortSw off off off off off off off
PortTime 0 0 0 0 0 0 0
PortMode fngr fngr fngr fngr fngr fngr
PB Upper +2 +2 +2 +2 +2 +2
PB Lower -2 -2 -2 -2 -2 -2
PB Trns on on on on on on
RB Trns on on on on on on
MW1 Trns on on on on on on
MW2 Trns on on on on on on
KN1 Trns on on on on on on
KN2 Trns on on on on on on
KN3 Trns on on on on on on
KN4 Trns on on on on on on
KN5 Trns on on on on on on
KN6 Trns on on on on on on
AT Trns on on on on on on
FC Trns on on on on on on
BC Trns on on on on on on
Sus Trns on on on on on on
FS Trns on on on on on on
FV Trns off off off off off off
CtrlToMD off off off off off off
CtrlToTG off off off off off off
KnobToMD off off off off off off
KnobToTG off off off off off off
PC toMD off off off off off off
Bank MSB 063 063 063 063 063 063
Bank LSB 000 000 000 000 000 000
MIDI PC 001 001 001 001 001 001
Init PB 64 64 64 64 64 64
Init MW1 0 0 0 0 0 0
Init MW2 64 64 64 64 64 64
Init AT 0 0 0 0 0 0
Init FC 127 127 127 127 127 127
Init BC 0 0 0 0 0 0
Init RB 64 64 64 64 64 64
Init KN1 64 64 64 64 64 64
Init KN2 64 64 64 64 64 64
Init KN3 64 64 64 64 64 64
Init KN4 64 64 64 64 64 64
Init KN5 64 64 64 64 64 64
Init KN6 64 64 64 64 64 64
Performance Job
Mode
These jobs let you initialize, recall or copy
performances that were created in Performance Edit
mode (or are being edited).
Press [JOB] key on the panel while in Performance
mode to enter Performance Job mode. When you enter
the Performance Job mode, the following menu will be
displayed. There are two types of jobs in Performance
Job mode. Press [F1] (INIT), [F2] (RECL), or [F3]
(COPY) to select a job.
It is necessary to first select the performance that will be
initialized, recalled or copied, before entering the
Performance Job mode (See page 172).
[F1]: INIT (Initialize)
[F2]: RECL(Recall)
[F2]: COPY (Copy)
Steps for Executing a Job
1 When in the Performance Play mode, select the
performance number you want to execute job
operation.
2 Press [JOB] to enter the Performance Job mode.
3 Press [F1] (INIT), [F2] (RECL), or [F3] (COPY) to
select a job to execute. The selected job screen will
be displayed.
You can also select each job by moving the cursor to the
desired job name on the screen and pressing [ENTER].
4 Move the cursor to a parameter and use the
[INC]/[DEC], Data dial, numeric keypad, or the
Knobs 1~6 to set values.
This operation is not necessary for Initialize and Recall.
F1 F2 F3
Performance/E/qx 5/21/98 11:35 AM Page 172