USRobotics V.34 - Manual (Page 236)

COURIER HIGH SPEED MODEMS
Index 1
INDEX
Command List Bold entries indicate primary references .
+++, return to Command mode, 4-10, C-2
+FAA, Call Detection, 5-4
+FCLASS=
n, Fax/Data mode, 5-2
+FCLASS?, display mode, 5-2
>, repeat, 4-7, C-3
/, pause, 4-5, C-5
$, basic command help, 6-8–6-11
&$, ampersand command help, 6-9
&A, enable ARQ result codes, 4-17–4-18, C-9
&B, computer or terminal/modem rate,
4-21–4-22, C-9
&C, Carrier Detect, 4-23, C-9
&D, Data Terminal Ready, 4-23–4-24, C-10
&F, load factory configurations, 4-11–4-12, C-10,
B-9–B-13
&G, Guard tone, 4-30, C-11
&H, Transmit Data flow control, 4-26–4-27,
C-11
&I, Received Data software flow control,
4-27–4-29, C-11–C-12
&K, Data compression, 4-20, C-12
&L, leased line operation, F-15
&M, error control, 4-19–4-20, C-12–C-13, F-6–F-7
&N, connection link rate, 4-22–4-23, C-13–C-14,
F-5, F-11–F-12
&P, make/break ratio, 4-31, C-14
&R, Received Data hardware flow control,
4-27, C-14
&S, Data Set Ready, 4-24, C-14–C-15
&T, test options, C-15, Appendix H
&W, write to NVRAM, 4-12, C-15
&X, synchronous timing source, F-3
&Y, break handling, 4-31, C-16
&Z
n=s, write number to NVRAM, 4-7, C-17
&Z n?, display number in NVRAM, 4-7, 6-7,
C-17
&ZC= s, store command string, 4-32, C-16–C-17
&ZC?, display stored command string, 4-32, C-
16
%$, percent command help, 6-11
%A, Dial Security accounts, C-18, D-4–D-5
%B, remote access, C-18, D-14
%C, remote access configuration control,
C-18, D-14–D-15
%E, erase Dial Security parameter(s), C-18–C-19,
D-8
%F, configure data format, C-19, D-15
%L, local security password, C-19, D-5
%N, synchronous DTE rate, C-19, F-4–F-5
%P
n=s, password security, C-19, D-10–D-11,
D-15
%P n?, display password, C-19, D-15
%S, Dial Security status, C-19, D-7
%T, Tone recognition, 4-32, C-20
%V, autopass password, C-20, D-9
A, force answer mode, 4-8, C-3
A/, repeat last command, 4-7, C-3
A>, continuous repeat, 4-8, C-3
Any key, terminate current operation, 4-3, C-3
AT, attention command prefix, 4-1, 4-3, C-1,
C-3
B, handshake options, 4-19, C-4
C, disable transmitter, 4-31, C-4
D, dial, 4-4–4-6, C-4
$, dial command help, 6-10
@, wait for an answer, 4-5, C-5
, (comma), pause, 4-4, C-4
/ (slash), short pause, 4-5, C-5
; (semi-colon), return to Command mode,
4-4, C-4
" (quotation mark), dial letters, 4-5, C-4
! (exclamation point), transfer call, 4-5, C-4
P, pulse dial, 4-4, C-4
R, reverse frequencies, 4-6, C-5
T, Tone dial, 4-4, C-4
W, wait for second dial tone, 4-5, C-4
DL, dial last-dialed number, 4-5, C-5
DL?, display last-dialed number, 6-8
DS, dial number stored in NVRAM, 4-6, C-5
E, Command mode local echo, 4-13, C-5
F, online local echo, 4-13–4-14, C-5
H, on/off hook control, 4-9, C-5
I, inquiry options, Chapter 6, C-6
K, modem clock, 4-31, C-6
L, speaker volume control, C-6
M, speaker control, 4-13, C-7
O, return online, 4-11, C-7
P, pulse dial, 4-4, C-4
Q, quiet mode, 4-14, C-7
S$, S-Register help, 6-10
Sr?, S-Register query, B-15, C-7
Sr=
n, set S-Register value, B-15, C-7
T, tone dial, 4-4, C-4
V, verbal/numeric mode, 4-14, C-7
X, result code options, 4-15–4-16, C-8
Z, reset to NVRAM settings, 4-13, C-8