Philips HDR3700 - Manual (Page 32)

32 EN
Press [STOP C] on the front panel of the
unit or [C (STOP)] on the remote control
to stop current timer recording.
• You can also stop the timer recording in progress by
deleting the timer programme. Press [TIMER] while
the timer recording is in progress, then follow steps
2 -A) and 3 of the “To Check/Delete/Amend Timer
Programme” on page 31.
The error number appears on “Timer Programming”
list.
The error numbers indicate:
• Timer programme with an error number will be
cleared once the entry screen for the
programme is displayed.
• If a power failure occurs or the unit is unplugged for
more than 30 seconds, the clock setting and all
timer settings will be lost.
• If a disc is not inserted or if a inserted disc is not
recordable (finalised DVD+R, finalised DVD-RW/-R,
a fully recorded disc, etc.), the unit will perform the
alternate recording to the HDD. (See page 31.)
• When a timer recording is completed, the unit will
ask you whether to turn off the unit if there is no
timer recording which starts within 4 minutes, except
under conditions listed below.
- During playback of HDD or DVD.
- While displaying menus or information on the
screen.
The unit will be turned off automatically if you select
“Yes” or if you do not reply in 1 minute.
• When the programmed starting and ending time are
earlier than the current time, the setting will not be
accepted.
• The audio language which is selected in the “Digital
TV Settings” will be recorded for the timer recording
of digital TV broadcasting.
• Timer recording whose recording time exceeds 12
hours cannot be made.
• It is prohibited to turn off the unit 4 minutes before
the programmed starting time.
• It is prohibited to change channel from 15 seconds
before the programmed starting time.
• [I (RECORD)] does not work from 2 minutes
before the programmed starting time. If it comes to 2
minutes before the starting time during regular or
one-touch timer recording, the recording in progress
will be stopped.
• Playback of DVD/CD is prohibited from 2 minutes
before the programmed starting time when the
recording media is DVD. If it comes to 2 minutes
before the programmed starting time during DVD/
CD playback, the playback will be stopped.
• When 2 or more programmes are overlapped,
“Timer programme overlapped” appears, and the
overlapped programme will be displayed in blue. To
correct the timer programme refer to “To Check/
Delete/Amend Timer Programme” on page 31.
• If the Start time is earlier and the End time is later
than the current time, the recording will start
immediately after you press [OK] at step
9 on
page 31.
To Stop Timer Recording in
Progress
Error Codes for Timer Recording
that Does Not Work Correctly
E1–E22,
E37–E39 : Recording error
E25/E51 :
:
• Copy prohibited programme
• Cannot record because of the
NTSC/PAL-60 signal is received.
E26–E28 : Copy prohibited programme
E30
: Disc full
E40 :
:
• There are some unrecorded parts
due the overlapped timer
programmes.
• Recording did not start at the start
time.
E41 : Power failure
E45 : Copy prohibited programme
E46 : You are trying to record onto the
unfinalised +VR mode discs recorded
on other unit.
E47 : Already 600 titles recorded on the
HDD.
E49 : There was no disc space on the HDD
at the starting time for the HDD timer
recording.
E50 : HDD recording is cancelled due to the
insufficiency of the disc space on the
HDD.
01/01 E40 12:00 13:00 1
Timer Programming
New Programme
TUE
CH End Start Date
01/01 12:00
STTL
Press TIMER to exit
Hints for the Timer Recording
E2N41BN_EN.book Page 32 Wednesday, July 2, 2008 4:36 PM