FARGO electronic DTC300 User Manual

Page 443

RESTRICTED USE ONLY

Fargo Electronics, Inc.

DTC400/DTC300/DTC300M Card Printer Service Manual (Rev. 1.3)

16-2

dimension boxes, 6-95
DIP switches (Dual In-line Package Switches), 15-4
Direct-to-Card (DTC) Printing, 15-5
Disable Printing option, 6-28, 6-40
Disables Magnetic Verification, 5-55
disk cleanup utility, 5-5
Dither, 15-5
DMA (Direct Memory Access), 15-3
Dongle, 15-5
Dot, 15-5
Dot pitch, 15-5
Download, 15-5
DPI (Dot Per Inch), 15-5
DRAM (Dynamic Random Access Memory), 15-5
Driver, 15-5
DTC400/DTC300/DTC300M Card Printer, 9-1
Duplex Printing, 15-5
Dwell Time, 15-6
Dye Migration, 15-6
Dye-Sub Intensity setting, 5-45
Dye-Sublimation, 2-8, 15-6
Dye-Sublimation Cyan Panel, 2-10
Dye-Sublimation Magenta Panel, 2-10
Dye-Sublimation Yellow Panel, 2-10
Dye-Sublimation-Only Print Ribbons, 2-12

E-card, 15-6
E-card Docking Station, 15-6
ECP Mode (Enhanced Capabilities Port Mode), 15-6
Edge-to-Edge, 15-6
EE Memory, 15-6
EEPROM (Electrically Erasable Programmable Read

Only Memory), 15-6

embedded contaminants, 2-14, 5-42
Emissions Standards, 2-3
EN 60950-1

2001, 2-2

Enable MLE Support checkbox, 6-56
Encoder (smart card), 15-6
Encoder (wheel), 15-7
encrypted secure code, 3-1
End Sentinel (ES)., 6-61
Engine, 15-7
EOF (End Of Form), 15-7
EPP (Enhanced Parallel Port), 15-7
EPROM (Electronically Programmable Read Only

Memory), 15-7

EPROM version number, 5-54, 5-56
Escape sequence, 15-7
ESD, 1-2, 6-4, 6-5, 7-2, 8-4, 10-1
ESD (ElectroStatic Discharge), 15-7
Ethernet, 15-7
excessive resin printing problems, 5-48
exposed to static electrical discharges, 7-3

Fargo Secure Print Security Suite, 3-1
Fargo Technical Support, 13-1
Fargo Technical Support via the Web, 13-1

FCC, 2-2
feed card into encoder, 5-5
Field Separator (FS), 6-61
Film, 15-7
Firmware, 15-7
five (5) applications, 3-2
Flash Memory, 15-8
Flipper Table Module, 2-15
Font, 15-8
For Overlay Only, 6-70
For Print and Overlay, 6-70
FPGA (Field Programmable Gate Array), 15-8
Front and Back radio buttons, 2-15
Front Cover, 2-9
Frontside and Backside options

K Panel Resin, 6-87, 6-88, 6-89
Overlay / Print Area, 6-65

Full bleed, 15-8
Full Card option, 6-68, 6-91

Gamma, 15-8
Glossy / Matte, 15-8
Glossy PVC, 15-8
Graphical Device Interface (GDI), 15-8
Gray Scale, 15-8

Halftoning, 15-8
Hard Drive, 15-9
hard Drive space

adequate or inadequate, 5-5

HDP (High Definition Printing™), 15-9
Head, 15-9
Headlift Motor Assembly, 8-63, 8-65, 8-66
Headlift Motors, 5-33
Headlift Sensors, 5-33
Heat Seal, 15-9
Heat sink, 15-9
HiCo (High Coercivity), 15-9
High Coercivity Magnetic Head Assembly Replacement,

8-75

high-resolution, 24-bit color images, 5-53
Horizontal adjustment, 6-47
HTML (HyperText Markup Language), 15-9
HTTP (HyperText Transfer Protocol), 15-9
Humidity, 2-4

IC (Integrated Circuit), 15-9
ID (Identification), 15-9
ID format, 6-23, 6-36
Identification Card sample, 6-95
IEEE 1284 (Institute of Electrical and Electronics

Engineers 1284), 15-10

Image, 15-10
Image Color tab, 6-21, 6-41
Image Darkness option, 6-106
Image Placement, 5-51, 5-52