ATN TITEW1000 Thermal Entry Wizard Access Control Station with Table Stand Mount - Manual (Page 5)

8 9
• Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected .
• Consult the dealer or an experienced radio/TV technician for help .
This equipment should be installed and operated with a minimum distance
20cm between the radiator and your body .
FCC CONDITIONS
This device complies with part 15 of the FCC Rules . Operation is subject to
the following two conditions:
1 . This device may not cause harmful interference .
2 . This device must accept any interference received, including interference
that may cause undesired operation .
EU CONFORMITY STATEMENT
This product and - if applicable - the supplied accessories too are
marked with "CE" and comply therefore with the applicable harmo-
nized European standards listed under the EMC Directive 2014/30/
EU, RE Directive 2014/53/EU,the RoHS Directive 2011/65/EU
2012/19/EU (WEEE directive): Products marked with this symbol
cannot be disposed of as unsorted municipal waste in the Europe-
an Union . For proper recycling, return this product to your local sup-
plier upon the purchase of equivalent new equipment, or dispose of
it at designated collection points . For more information see: www .re-
cyclethis .info
2006/66/EC (battery directive): This product contains a battery that
cannot be disposed of as unsorted municipal waste in the European
Union . See the product documentation for specific battery informa-
tion . The battery is marked with this symbol, which may include letter-
ing to indicate cadmium (Cd), lead (Pb), or mercury (Hg) . For proper
recycling, return the battery to your supplier or to a designated collec-
tion point . For more information see: www .recyclethis .info
SA FE T Y I N S T R U C T I O N
These instructions are intended to ensure that user can use the product cor-
rectly to avoid danger or property loss .
The precaution measure is divided into Dangers and Cautions:
Dangers. Neglecting any of the warnings may cause serious injury or death .
Follow these safeguards to prevent serious injury or death .
Cautions: Neglecting any of the cautions may cause injury or equipment
damage . Follow these precautions to prevent potential injury or material dam-
age .
DANGER
• All the electronic operation should be strictly compliance with the electri-
cal safety regulations, fire prevention regulations and other related regu-
lations in your local region .
• Please use the power adapter, which is provided . This equipment is in-
tended to be supplied from the Class 2 surge protected power source rat-
ed DC 12V, 3A .
• Do not connect several devices to one power adapter as adapter overload
may cause over-heat or fire hazard .
• Please make sure that the power has been disconnected before you wire,
install or dismantle the device .
• When the product is installed on wall or ceiling, the device shall be firm-
ly fixed .
• If smoke, odors or noise rise from the device, turn off the power at once
and unplug the power cable, and then please contact the service center .
• Do not ingest battery, Chemical Burn Hazard .
• This product contains a coin/button cell battery . If the coin/button cell bat-
tery is swallowed, it can cause severe internal burns in just 2 hours and
can lead to death .
• Keep new and used batteries away from children . If the battery compart-
ment does not close securely, stop using the product and keep it away
from children . If you think batteries might have been swallowed or placed
inside any part of the body, seek immediate medical attention .
• If the product does not work properly, please contact your dealer or the
nearest service center . Never attempt to disassemble the device yourself .
(We shall not assume any responsibility for problems caused by unautho-
rized repair or maintenance .)
CAUTIONS
• Do not drop the device or subject it to physical shock, and do not expose
it to high electromagnetism radiation . Avoid the equipment installation on
vibrations surface or places subject to shock (ignorance can cause equip-
ment damage) .
• Do not place the device in extremely hot (refer to the specification of the
device for the detailed operating temperature), cold, dusty or damp loca-
tions, and do not expose it to high electromagnetic radiation .
• The device cover for indoor use shall be kept from rain and moisture .
• Exposing the equipment to direct sun light, low ventilation or heat source
such as heater or radiator is forbidden (ignorance can cause fire danger) .
• Do not aim the device at the sun or extra bright places . A blooming or
smear may occur otherwise (which is not a malfunction however) and af-
fecting the endurance of sensor at the same time .
• Please use the provided glove when open up the device cover, avoid di-
rect contact with the device cover, because the acidic sweat of the fingers
may erode the surface coating of the device cover .
• Please use a soft and dry cloth when clean inside and outside surfaces of
the device cover, do not use alkaline detergents .
• Please keep all wrappers after unpack them for future use . In case of any
failure occurred, you need to return the device to the factory with the orig-
inal wrapper . Transportation without the original wrapper may result in
damage on the device and lead to additional costs .
• Improper use or replacement of the battery may result in hazard of explo-
sion . Replace with the same or equivalent type only . Dispose of used bat-
teries according to the instructions provided by the battery manufacturer .