ATN TITEW1000 Thermal Entry Wizard Access Control Station with Table Stand Mount - Manual (Page 19)

36 37
NOTE
Make sure your face picture is in the face picture outline when adding
the face picture.
Make sure the captured face picture is in good quality and is accurate.
For details about the instructions of adding face pictures, see Tips
When Collecting/Comparing Face Picture.
After completely adding the face picture, a captured face picture will be dis-
played at the upper right corner of the page .
7 . Tap Save to save the face picture .
8 . Optional: Tap Try Again and adjust your face position to add the face pic-
ture again .
NOTE
The maximum duration for adding a face picture is 15s. You can check
the remaining time for adding a face picture on the left of the page.
9 . Enable or disable the Administrator Permission function .
Enable Administrator Permission
The user is an administrator . Except for the normal attendance function, the
user can also enter the Home page to operate after authenticating the permis-
sion .
Disable Administrator Permission
The User is a normal user . The user can only authenticate or take atten-
dance on the initial page .
10 . Tap to save the settings .
6.4.3. Add Card
Add a card for the user and the user can authenticate via the added card .
Steps
1 . Long tap on the initial page and log in the backend .
2 . Tap User
→ + to enter the Add User page .
3 . Tap the Employee ID . field and edit the employee ID .
NOTE
The employee ID should be less than 32 characters. And it can be a
combination of lower letters, upper letters, and numbers.
The employee ID should not be duplicated.
4 . Tap the Name field and input the user name on the soft keyboard .
NOTE
Numbers, upper case letters, lower case letters, and special characters
are allowed in the user name.
Up to 32 characters are allowed in the user name.
5 . Tap the Card field and input the card No .
6 . Configure the card No .
Enter the card No . manually . Swipe the card over the card swiping area to
get the card No .
NOTE
The card No. cannot be empty.
Up to 20 characters are allowed in the card No.
The card No. cannot be duplicated.
7 . Optional: Enable the Duress Card function . The added card
When the user authenticates by swiping this duress card, the device will up-
load an duress card event to the client software .
8 . Enable or disable the Administrator Permission function .
Enable Administrator Permission
The user is an administrator . Except for the normal attendance function, the us-
er can also enter the Home page to operate after authenticating the permission .
Disable Administrator Permission
The User is a normal user . The user can only authenticate or take atten-
dance on the initial page .
9 . Tap to save the settings .
6.4.4. Add Password
Add a password for the user and the user can authenticate via the password .
Steps
1 . Long tap on the initial page and log in the backend .
2 . Tap User
→ + to enter the Add User page .
3 . Tap the Employee ID . field and edit the employee ID .
NOTE
The employee ID should be less than 32 characters. And it can be a
combination of lower letters, upper letters, and numbers.
The employee ID should not be duplicated.
4 . Tap the Name field and input the user name on the soft keyboard .
NOTE
Numbers, upper case letters, lower case letters, and special characters
are allowed in the user name.
Up to 32 characters are allowed in the user name.
5 . Tap the Password field and create a password and confirm the password .
NOTE
Only numbers are allowed in the password.
Up to 8 characters are allowed in the password.
6 . Enable or disable the Administrator Permission function .
Enable Administrator Permission
The user is an administrator . Except for the normal attendance function, the us-
er can also enter the Home page to operate after authenticating the permission .
Disable Administrator Permission
The User is a normal user . The user can only authenticate or take atten-
dance on the initial page .
7 . Tap to save the settings .