ATN TITEW1000 Thermal Entry Wizard Access Control Station with Table Stand Mount User Manual

Page 44

Before setting the capture parameters, you should set the picture stor-

age first to define where the event triggered pictures are saved. For details,

refer to Set Picture Storage in the user manual of the client software.

Set Triggered Capture Parameters

When an event occurs, the camera of the access control device can be trig-

gered to capture picture(s) to record what happens when the event occurs .

You can view the captured pictures when checking the event details in Event

Center . Before that, you need to set the parameters for the capture such as

number of pictures captured for one time .

Before You Start

Before setting the capture parameters, you should set the picture storage

first to define where the captured pictures are saved . For details, refer to Set

Picture Storage in the user manual of the client software .

Steps

NOTE

This function should be supported by the device.

1 . Enter the Access Control module .
2 . On the navigation bar on the left, enter Advanced Function

→

More Pa-

rameters

→

Capture .

3 . Select an access control device in the device list and select Linked

Capture .

4 . Set the picture size and quality .
5 . Set the capture times once triggered which defines how many pic-

tures will be captures for one time .

6 . If the capture times is more than 1, set the interval for each capture .
7 . Click Save .

Set Manual Capture Parameters

In Status Monitoring module, you can capture a picture manually the access

control device's camera by clicking a button . Before that, you need to set the

parameters for the capture such as picture quality .

Before You Start

Before setting the capture parameters, you should set the saving path first to

define where the captured pictures are saved . For details, refer to Set Picture

Storage in the user manual of the client software .

Steps

NOTE

This function should be supported by the device.

1 . Enter the Access Control module .
2 . On the navigation bar on the left, enter Advanced Function

→

More Pa-

rameters

→

Capture .

3 . Select an access control device in the device list and select Manual Cap-

ture .

4 . Select the resolution of the captured pictures from the drop-down list .
5 . Select the picture quality as High, Medium, or Low . The higher the pic-

ture quality is, the larger size the picture will be .

6 . Click Save .

Set Parameters for Face Recognition Terminal

For face recognition terminal, you can set its parameters including face pic-

ture database, etc .

Steps

NOTE

This function should be supported by the device.

1 . Enter the Access Control module .
2 . On the navigation bar on the left, enter Advanced Function

→

More Pa-

rameters .

3 . Select an access control device in the device list and click Face Recog-

nition Terminal .

4 . Set the parameters .

NOTE

These parameters displayed vary according to different device models.

Algorithm

Select Deep Learning as the face picture database .
Save Authenticating Face Picture
If enabled, the captured face picture when authenticating will be saved on

the device .

ECO Mode

After enabling the ECO mode, the device can authenticate faces in the low

light or dark environment . And you can set he ECO mode threshold, ECO

mode (1:N), and ECO mode (1:1) .

ECO Mode (1:1)

Set the matching threshold when authenticating via ECO mode 1:1 match-

ing mode . The larger the value, the smaller the false accept rate and the larg-

er the false rejection rate .

ECO Mode (1:N)

Set the matching threshold when authenticating via ECO mode 1:N match-

ing mode . The larger the value, the smaller the false accept rate and the larg-

er the false rejection rate .

ECO Mode Threshold

When enabling the ECO mode, you can set the ECO mode's threshold .

The larger the value, the easier the device entering the ECO mode . Available

range: 0 to 8 .

Work Mode

Set the device work mode as Access Control Mode . The access control

mode is the device normal mode . You should authenticate your credential for

accessing .

5 . Click Save .

Enable M1 Card Encryption

M1 card encryption can improve the security level of authentication .

Steps

NOTE

The function should be supported by the access control device and the

card reader.