ATN TITEW1000 Thermal Entry Wizard Access Control Station with Table Stand Mount User Manual

Page 30

Password

Enter the device password .

CAUTION

The password strength of the device can be automatically checked.

We highly recommend you change the password of your own choosing

(using a minimum of 8 characters, including at least three kinds of fol-

lowing categories: upper case letters, lower case letters, numbers, and

special characters) in order to increase the security of your product.

And we recommend you change your password regularly, especially in

the high security system, changing the password monthly or weekly can

better protect your product.

Proper configuration of all passwords and other security settings is the

responsibility of the installer and/or end-user.

6 . Optional: Check Transmission Encryption (TLS) to enable transmission

encryption using TLS (Transport Layer Security) protocol for security pur-

pose .

NOTE

This function should be supported by the device.
If you have enabled Certificate Verification, you should click Open

Certificate Folder to open the default folder and copy the certificate file

exported from the device to this default directory to strengthen the secu-

rity. See for details about enabling certificate verification.

You can log into the device to get the certificate file by web browser.

7 . Check Synchronize Time to synchronize the device time with the PC run-

ning the client after adding the device to the client .

8 . Optional: Check Import to Group to create a group by the device name

and import all the channels of the device to the group .

9 . Finish adding the device .
• Click Add to add the device and back to the device list page .
• Click Add and New to save the settings and continue to add other device .

Add Device by ISUP Account

For access control devices supports ISUP 5 .0 protocol, you can add them to

the client by ISUP protocol after entering device ID and key, if you have config-

ured their server addresses, port No ., and device IDs .

Before You Start

Make sure the devices have connected to the network properly .

Steps

1 . Enter Device Management module .
The added devices are displayed on the right panel .
2 . Click Add to open the Add window .
3 . Select ISUP as the adding mode .
4 . Enter the required information .

Device Account

Enter the account name registered on ISUP protocol .

ISUP Key

For ISUP 5 .0 devices, enter the ISUP key if you have set it when configuring

network center parameter for the device .

NOTE

This function should be supported by the device.

5 . Optional: Check Synchronize Time to synchronize the device time with

the PC running the client after adding the device to the client .

6 . Optional: Check Import to Group to create a group by the device name

and import all the channels of the device to the group .

7 . Finish adding the device .
• Click Add to add the device and go back to the device list .
• Click Add and New to save the settings and continue to add other device .
8 . Optional: Perform the following operation(s) .

Device Status

Click

on Operation column to view device status .

Edit Device

Information

Click

on Operation column to edit the device information,

such as device name, device account, and ISUP key .

Check Online User

Click

on Operation column to check the online users who

access the device, such as user name, user type, user's IP

address, and login time .

Refresh

Click

on Operation column to get the latest device

information .

Delete Device

Select one or multiple devices and click Delete to delete the

selected device(s) from the client .

Import Devices in a Batch

You can add multiple devices to the client in a batch by entering the device

parameters in a pre-defined CSV file .

Steps

1 . Enter the Device Management module .
2 . Click Device tab on the top of the right panel .
3 . Click Add to open the Add window, and then select Batch Import as the

adding mode .

4 . Click Export Template and then save the pre-defined template (CSV file)

on your PC .

5 . Open the exported template file and enter the required information of the

devices to be added on the corresponding column .

NOTE

For detailed description of the required fields, refer to the introduc-

tions in the template.

Adding Mode

Enter 0 or 1 or 2 .

Address

Edit the address of the device .

Port

Enter the device port number . The default port number is 8000 .

User Name

Enter the device user name . By default, the user name is admin .