H3C Technologies H3C S10500 Series Switches User Manual

Page 98

[DeviceC-rrpp-domain2] ring 1 enable

# Configure Device C as the edge node of subring 2 in RRPP domain 2, with GigabitEthernet 1/0/3 as

the edge port, and enable subring 2.

[DeviceC-rrpp-domain2] ring 2 node-mode edge edge-port gigabitethernet 1/0/3

[DeviceC-rrpp-domain2] ring 2 enable

[DeviceC-rrpp-domain2] quit

# Enable RRPP.

[DeviceC] rrpp enable

Configure Device D.

# Create VLANs 1 and 2, map VLAN 1 to MSTI 1 and VLAN 2 to MSTI 2, and activate MST region

configuration.

system-view

[DeviceD] vlan 1 to 2

[DeviceD] stp region-configuration

[DeviceD-mst-region] instance 1 vlan 1

[DeviceD-mst-region] instance 2 vlan 2

[DeviceD-mst-region] active region-configuration

[DeviceD-mst-region] quit

# Cancel the physical state change suppression interval setting on GigabitEthernet 1/0/1 and
GigabitEthernet 1/0/2, and disable the spanning tree feature. Configure the two ports as trunk ports,

and assign them to VLAN 1 and VLAN 2.

[DeviceD] interface gigabitethernet 1/0/1

[DeviceD-GigabitEthernet1/0/1] undo link-delay

[DeviceD-GigabitEthernet1/0/1] undo stp enable

[DeviceD-GigabitEthernet1/0/1] port link-type trunk

[DeviceD-GigabitEthernet1/0/1] port trunk permit vlan 1 2

[DeviceD-GigabitEthernet1/0/1] quit

[DeviceD] interface gigabitethernet 1/0/2

[DeviceD-GigabitEthernet1/0/2] undo link-delay

[DeviceD-GigabitEthernet1/0/2] undo stp enable

[DeviceD-GigabitEthernet1/0/2] port link-type trunk

[DeviceD-GigabitEthernet1/0/2] port trunk permit vlan 1 2

[DeviceD-GigabitEthernet1/0/2] quit

# Create RRPP domain 1. Configure VLAN 100 as the primary control VLAN of RRPP domain 1, and
configure the VLAN mapped to MSTI 1 as the protected VLAN of RRPP domain 1.

[DeviceD] rrpp domain 1

[DeviceD-rrpp-domain1] control-vlan 100

[DeviceD-rrpp-domain1] protected-vlan reference-instance 1

# Configure Device D as the transit node of primary ring 1 in RRPP domain 1, with GigabitEthernet

1/0/1 as the primary port and GigabitEthernet 1/0/2 as the secondary port, and enable ring 1.

[DeviceD-rrpp-domain1] ring 1 node-mode transit primary-port gigabitethernet 1/0/1

secondary-port gigabitethernet 1/0/2 level 0

[DeviceD-rrpp-domain1] ring 1 enable

[DeviceD-rrpp-domain1] quit

# Create RRPP domain 2. Configure VLAN 105 as the primary control VLAN of RPPP domain 2, and
configure the VLAN mapped to MSTI 2 as the protected VLAN of RRPP domain 2.

This manual is related to the following products:

H3C S5800 Series Switches H3C S5820X Series Switches H3C WX3000E Series Wireless Switches H3C SecPath F1000-E H3C SecPath F5000-A5 Firewall H3C SecPath F1000-A-EI H3C SecPath F1000-E-SI H3C SecPath F1000-S-AI H3C SecPath F5000-S Firewall H3C SecPath F5000-C Firewall H3C SecPath F100-C-SI H3C SecPath F1000-C-SI H3C SecPath F100-A-SI H3C SecBlade FW Cards H3C SecBlade FW Enhanced Cards H3C SecPath U200-A U200-M U200-S H3C SecPath U200-CA U200-CM U200-CS