H3C Technologies H3C S10500 Series Switches User Manual

Page 100

[DeviceE-rrpp-domain2] ring 2 node-mode master primary-port gigabitethernet 1/0/2

secondary-port gigabitethernet 1/0/1 level 1

[DeviceE-rrpp-domain2] ring 2 enable

[DeviceE-rrpp-domain2] quit

# Enable RRPP.

[DeviceE] rrpp enable

Configure Device F.

# Create VLAN 1, map VLAN 1 to MSTI 1, and activate MST region configuration.

system-view

[DeviceF] vlan 1

[DeviceF-vlan1] quit

[DeviceF] stp region-configuration

[DeviceF-mst-region] instance 1 vlan 1

[DeviceF-mst-region] active region-configuration

[DeviceF-mst-region] quit

# Cancel the physical state change suppression interval setting on GigabitEthernet 1/0/1 and
GigabitEthernet 1/0/2, and disable the spanning tree feature. Configure the two ports as trunk ports,

and assign them to VLAN 1.

[DeviceF] interface gigabitethernet 1/0/1

[DeviceF-GigabitEthernet1/0/1] undo link-delay

[DeviceF-GigabitEthernet1/0/1] undo stp enable

[DeviceF-GigabitEthernet1/0/1] port link-type trunk

[DeviceF-GigabitEthernet1/0/1] port trunk permit vlan 1

[DeviceF-GigabitEthernet1/0/1] quit

[DeviceF] interface gigabitethernet 1/0/2

[DeviceF-GigabitEthernet1/0/2] undo link-delay

[DeviceF-GigabitEthernet1/0/2] undo stp enable

[DeviceF-GigabitEthernet1/0/2] port link-type trunk

[DeviceF-GigabitEthernet1/0/2] port trunk permit vlan 1

[DeviceF-GigabitEthernet1/0/2] quit

# Create RRPP domain 1. Configure VLAN 100 as the primary control VLAN, and configure the VLAN
mapped to MSTI 1 as the protected VLAN.

[DeviceF] rrpp domain 1

[DeviceF-rrpp-domain1] control-vlan 100

[DeviceF-rrpp-domain1] protected-vlan reference-instance 1

# Configure Device F as the master node of subring 3 in RRPP domain 1, with GigabitEthernet 1/0/1 as
the primary port and GigabitEthernet 1/0/2 as the secondary port, and enable subring 3.

[DeviceF-rrpp-domain1] ring 3 node-mode master primary-port gigabitethernet 1/0/1

secondary-port gigabitethernet 1/0/2 level 1

[DeviceF-rrpp-domain1] ring 3 enable

[DeviceF-rrpp-domain1] quit

# Enable RRPP.

[DeviceF] rrpp enable

RRPP ring group configurations on Device B and Device C after the configurations.

# Create RRPP ring group 1 on Device B. Add subrings 2 and 3 to the RRPP ring group.

[DeviceB] rrpp ring-group 1

This manual is related to the following products:

H3C S5800 Series Switches H3C S5820X Series Switches H3C WX3000E Series Wireless Switches H3C SecPath F1000-E H3C SecPath F5000-A5 Firewall H3C SecPath F1000-A-EI H3C SecPath F1000-E-SI H3C SecPath F1000-S-AI H3C SecPath F5000-S Firewall H3C SecPath F5000-C Firewall H3C SecPath F100-C-SI H3C SecPath F1000-C-SI H3C SecPath F100-A-SI H3C SecBlade FW Cards H3C SecBlade FW Enhanced Cards H3C SecPath U200-A U200-M U200-S H3C SecPath U200-CA U200-CM U200-CS