H3C Technologies H3C S10500 Series Switches User Manual

Page 91

[DeviceF-GigabitEthernet1/0/1] quit

[DeviceF] interface gigabitethernet 1/0/2

[DeviceF-GigabitEthernet1/0/2] undo link-delay

[DeviceF-GigabitEthernet1/0/2] undo stp enable

[DeviceF-GigabitEthernet1/0/2] port link-type trunk

[DeviceF-GigabitEthernet1/0/2] port trunk permit vlan 1 to 30

[DeviceF-GigabitEthernet1/0/2] quit

# Create RRPP domain 1. Configure VLAN 4092 as the primary control VLAN of RRPP domain 1, and

configure the VLANs mapped to MSTI 1 as the protected VLANs of RRPP domain 1.

[DeviceF] rrpp domain 1

[DeviceF-rrpp-domain1] control-vlan 4092

[DeviceF-rrpp-domain1] protected-vlan reference-instance 1

# Configure Device F as the master node of subring 3, with GigabitEthernet 1/0/1 as the primary port
and GigabitEthernet 1/0/2 as the secondary port, and enable subring 3.

[DeviceF-rrpp-domain1] ring 3 node-mode master primary-port gigabitethernet 1/0/1

secondary-port gigabitethernet 1/0/2 level 1

[DeviceF-rrpp-domain1] ring 3 enable

[DeviceF-rrpp-domain1] quit

# Enable RRPP.

[DeviceF] rrpp enable

Configure Device G.

# Create VLANs 1 through 30, map these VLANs to MSTI 1, and activate the MST region configuration.

system-view

[DeviceG] vlan 1 to 30

[DeviceG] stp region-configuration

[DeviceG-mst-region] instance 1 vlan 1 to 30

[DeviceG-mst-region] active region-configuration

[DeviceG-mst-region] quit

# Cancel the physical state change suppression interval setting on GigabitEthernet 1/0/1 and

GigabitEthernet 1/0/2, and disable the spanning tree feature. Configure the two ports as trunk ports,
and assign them to VLANs 1 through 30.

[DeviceG] interface gigabitethernet 1/0/1

[DeviceG-GigabitEthernet1/0/1] undo link-delay

[DeviceG-GigabitEthernet1/0/1] undo stp enable

[DeviceG-GigabitEthernet1/0/1] port link-type trunk

[DeviceG-GigabitEthernet1/0/1] port trunk permit vlan 1 to 30

[DeviceG-GigabitEthernet1/0/1] quit

[DeviceG] interface gigabitethernet 1/0/2

[DeviceG-GigabitEthernet1/0/2] undo link-delay

[DeviceG-GigabitEthernet1/0/2] undo stp enable

[DeviceG-GigabitEthernet1/0/2] port link-type trunk

[DeviceG-GigabitEthernet1/0/2] port trunk permit vlan 1 to 30

[DeviceG-GigabitEthernet1/0/2] quit

# Create RRPP domain 1. Configure VLAN 4092 as the primary control VLAN of RRPP domain 1, and
configure the VLANs mapped to MSTI 1 as the protected VLANs of RRPP domain 1.

[DeviceG] rrpp domain 1

This manual is related to the following products:

H3C S5800 Series Switches H3C S5820X Series Switches H3C WX3000E Series Wireless Switches H3C SecPath F1000-E H3C SecPath F5000-A5 Firewall H3C SecPath F1000-A-EI H3C SecPath F1000-E-SI H3C SecPath F1000-S-AI H3C SecPath F5000-S Firewall H3C SecPath F5000-C Firewall H3C SecPath F100-C-SI H3C SecPath F1000-C-SI H3C SecPath F100-A-SI H3C SecBlade FW Cards H3C SecBlade FW Enhanced Cards H3C SecPath U200-A U200-M U200-S H3C SecPath U200-CA U200-CM U200-CS