H3C Technologies H3C S10500 Series Switches - Manual (Page 123)

114
[DeviceA] interface gigabitethernet 1/0/1
[DeviceA-GigabitEthernet1/0/1] cfd mep 1002 service-instance 1 outbound
[DeviceA-GigabitEthernet1/0/1] cfd mep service-instance 1 mep 1002 enable
[DeviceA-GigabitEthernet1/0/1] cfd cc service-instance 1 mep 1002 enable
[DeviceA-GigabitEthernet1/0/1] quit
# Create MA MA_B for the MD and configure the MA to serve VLAN 110, and create service instance
2 for the MD and MA.
[DeviceA] cfd ma MA_B md MD vlan 110
[DeviceA] cfd service-instance 2 md MD ma MA_B
# Create a MEP list in service instance 2, create and enable outward-facing MEP 1002, and enable
CCM sending in service instance 2 on GigabitEthernet 1/0/2.
[DeviceA] cfd meplist 2001 2002 service-instance 2
[DeviceA] interface gigabitethernet 1/0/2
[DeviceA-GigabitEthernet1/0/2] cfd mep 2002 service-instance 2 outbound
[DeviceA-GigabitEthernet1/0/2] cfd mep service-instance 2 mep 2002 enable
[DeviceA-GigabitEthernet1/0/2] cfd cc service-instance 2 mep 2002 enable
[DeviceA-GigabitEthernet1/0/2] quit
2. Configure Device B.
# Create VLAN 1 through VLAN 200.
system-view
[DeviceB] vlan 1 to 200
# Configure GigabitEthernet 1/0/1 as a trunk port and assign it to VLANs 1 through 200. Enable flush
message receiving and configure VLAN 10 and VLAN 110 as the receive control VLANs on
GigabitEthernet 1/0/1.
[DeviceB] interface gigabitethernet 1/0/1
[DeviceB-GigabitEthernet1/0/1] port link-type trunk
[DeviceB-GigabitEthernet1/0/1] port trunk permit vlan 1 to 200
[DeviceB-GigabitEthernet1/0/1] smart-link flush enable control-vlan 10 110
[DeviceB-GigabitEthernet1/0/1] quit
# Configure GigabitEthernet 1/0/2 as a trunk port and assign it to VLANs 1 through 200. Disable the
spanning tree feature and enable flush message receiving on it, and configure VLAN 10 and VLAN 110
as the receive control VLANs.
[DeviceB] interface gigabitethernet 1/0/2
[DeviceB-GigabitEthernet1/0/2] port link-type trunk
[DeviceB-GigabitEthernet1/0/2] port trunk permit vlan 1 to 200
[DeviceB-GigabitEthernet1/0/2] undo stp enable
[DeviceB-GigabitEthernet1/0/2] smart-link flush enable control-vlan 10 110
[DeviceB-GigabitEthernet1/0/2] quit
3. Configure Device C.
# Create VLAN 1 through VLAN 200, map VLANs 1 through 100 to MSTI 1, and VLANs 101 through
200 to MSTI 2, and activate MST region configuration.
system-view
[DeviceC] vlan 1 to 200
[DeviceC] stp region-configuration
[DeviceC-mst-region] instance 1 vlan 1 to 100
[DeviceC-mst-region] instance 2 vlan 101 to 200