H3C Technologies H3C S10500 Series Switches User Manual

Page 89

[DeviceD-GigabitEthernet1/0/1] port trunk permit vlan 1 to 30

[DeviceD-GigabitEthernet1/0/1] quit

[DeviceD] interface gigabitethernet 1/0/2

[DeviceD-GigabitEthernet1/0/2] undo link-delay

[DeviceD-GigabitEthernet1/0/2] undo stp enable

[DeviceD-GigabitEthernet1/0/2] port link-type trunk

[DeviceD-GigabitEthernet1/0/2] port trunk permit vlan 1 to 30

[DeviceD-GigabitEthernet1/0/2] quit

[DeviceD] interface gigabitethernet 1/0/3

[DeviceD-GigabitEthernet1/0/3] undo link-delay

[DeviceD-GigabitEthernet1/0/3] undo stp enable

[DeviceD-GigabitEthernet1/0/3] port link-type trunk

[DeviceD-GigabitEthernet1/0/3] port trunk permit vlan 1 to 30

[DeviceD-GigabitEthernet1/0/3] quit

[DeviceD] interface gigabitethernet 1/0/4

[DeviceD-GigabitEthernet1/0/4] undo link-delay

[DeviceD-GigabitEthernet1/0/4] undo stp enable

[DeviceD-GigabitEthernet1/0/4] port link-type trunk

[DeviceD-GigabitEthernet1/0/4] port trunk permit vlan 1 to 30

[DeviceD-GigabitEthernet1/0/4] quit

# Create RRPP domain 1. Configure VLAN 4092 as the primary control VLAN of RRPP domain 1, and
configure the VLANs mapped to MSTI 1 as the protected VLANs of RRPP domain 1.

[DeviceD] rrpp domain 1

[DeviceD-rrpp-domain1] control-vlan 4092

[DeviceD-rrpp-domain1] protected-vlan reference-instance 1

# Configure Device D as the transit node of primary ring 1, with GigabitEthernet 1/0/1 as the primary
port and GigabitEthernet 1/0/2 as the secondary port, and enable ring 1.

[DeviceD-rrpp-domain1] ring 1 node-mode transit primary-port gigabitethernet 1/0/1

secondary-port gigabitethernet 1/0/2 level 0

[DeviceD-rrpp-domain1] ring 1 enable

# Configure Device D as the edge node of subring 4, with GigabitEthernet 1/0/3 as the edge port, and
enable subring 4.

[DeviceD-rrpp-domain1] ring 4 node-mode edge edge-port gigabitethernet 1/0/3

[DeviceD-rrpp-domain1] ring 4 enable

# Configure Device D as the edge node of subring 5, with GigabitEthernet 1/0/4 as the edge port, and
enable subring 5.

[DeviceD-rrpp-domain1] ring 5 node-mode edge edge-port gigabitethernet 1/0/4

[DeviceD-rrpp-domain1] ring 5 enable

[DeviceD-rrpp-domain1] quit

# Enable RRPP.

[DeviceD] rrpp enable

Configure Device E.

# Create VLANs 1 through 30, map these VLANs to MSTI 1, and activate the MST region configuration.

system-view

[DeviceE] vlan 1 to 30

[DeviceE] stp region-configuration

This manual is related to the following products:

H3C S5800 Series Switches H3C S5820X Series Switches H3C WX3000E Series Wireless Switches H3C SecPath F1000-E H3C SecPath F5000-A5 Firewall H3C SecPath F1000-A-EI H3C SecPath F1000-E-SI H3C SecPath F1000-S-AI H3C SecPath F5000-S Firewall H3C SecPath F5000-C Firewall H3C SecPath F100-C-SI H3C SecPath F1000-C-SI H3C SecPath F100-A-SI H3C SecBlade FW Cards H3C SecBlade FW Enhanced Cards H3C SecPath U200-A U200-M U200-S H3C SecPath U200-CA U200-CM U200-CS