H3C Technologies H3C S10500 Series Switches User Manual

Page 94

[DeviceA] stp region-configuration

[DeviceA-mst-region] instance 1 vlan 1

[DeviceA-mst-region] instance 2 vlan 2

[DeviceA-mst-region] active region-configuration

[DeviceA-mst-region] quit

# Cancel the physical state change suppression interval setting on GigabitEthernet 1/0/1 and
GigabitEthernet 1/0/2, and disable the spanning tree feature. Configure the two ports as trunk ports,

and assign them to VLAN 1 and VLAN 2.

[DeviceA] interface gigabitethernet 1/0/1

[DeviceA-GigabitEthernet1/0/1] undo link-delay

[DeviceA-GigabitEthernet1/0/1] undo stp enable

[DeviceA-GigabitEthernet1/0/1] port link-type trunk

[DeviceA-GigabitEthernet1/0/1] port trunk permit vlan 1 2

[DeviceA-GigabitEthernet1/0/1] quit

[DeviceA] interface gigabitethernet 1/0/2

[DeviceA-GigabitEthernet1/0/2] undo link-delay

[DeviceA-GigabitEthernet1/0/2] undo stp enable

[DeviceA-GigabitEthernet1/0/2] port link-type trunk

[DeviceA-GigabitEthernet1/0/2] port trunk permit vlan 1 2

[DeviceA-GigabitEthernet1/0/2] quit

# Create RRPP domain 1. Configure VLAN 100 as the primary control VLAN of RRPP domain 1, and
configure the VLAN mapped to MSTI 1 as the protected VLAN of RRPP domain 1.

[DeviceA] rrpp domain 1

[DeviceA-rrpp-domain1] control-vlan 100

[DeviceA-rrpp-domain1] protected-vlan reference-instance 1

# Configure Device A as the master node of primary ring 1, with GigabitEthernet 1/0/1 as the primary

port and GigabitEthernet 1/0/2 as the secondary port, and enable ring 1.

[DeviceA-rrpp-domain1] ring 1 node-mode master primary-port gigabitethernet 1/0/1

secondary-port gigabitethernet 1/0/2 level 0

[DeviceA-rrpp-domain1] ring 1 enable

[DeviceA-rrpp-domain1] quit

# Create RRPP domain 2, configure VLAN 105 as the primary control VLAN of RRPP domain 2, and
configure the VLAN mapped to MSTI 2 as the protected VLAN of RRPP domain 2.

[DeviceA] rrpp domain 2

[DeviceA-rrpp-domain2] control-vlan 105

[DeviceA-rrpp-domain2] protected-vlan reference-instance 2

# Configure Device A as the master node of primary ring 1, with GigabitEthernet 1/0/2 as the master
port and GigabitEthernet 1/0/1 as the secondary port, and enable ring 1.

[DeviceA-rrpp-domain2] ring 1 node-mode master primary-port gigabitethernet 1/0/2

secondary-port gigabitethernet 1/0/1 level 0

[DeviceA-rrpp-domain2] ring 1 enable

[DeviceA-rrpp-domain2] quit

# Enable RRPP.

[DeviceA] rrpp enable

Configure Device B.

This manual is related to the following products:

H3C S5800 Series Switches H3C S5820X Series Switches H3C WX3000E Series Wireless Switches H3C SecPath F1000-E H3C SecPath F5000-A5 Firewall H3C SecPath F1000-A-EI H3C SecPath F1000-E-SI H3C SecPath F1000-S-AI H3C SecPath F5000-S Firewall H3C SecPath F5000-C Firewall H3C SecPath F100-C-SI H3C SecPath F1000-C-SI H3C SecPath F100-A-SI H3C SecBlade FW Cards H3C SecBlade FW Enhanced Cards H3C SecPath U200-A U200-M U200-S H3C SecPath U200-CA U200-CM U200-CS