H3C Technologies H3C S10500 Series Switches - Manual (Page 95)

86
# Create VLANs 1 and 2, map VLAN 1 to MSTI 1 and VLAN 2 to MSTI 2, and activate MST region
configuration.
system-view
[DeviceB] vlan 1 to 2
[DeviceB] stp region-configuration
[DeviceB-mst-region] instance 1 vlan 1
[DeviceB-mst-region] instance 2 vlan 2
[DeviceB-mst-region] active region-configuration
[DeviceB-mst-region] quit
# Cancel the physical state change suppression interval setting on GigabitEthernet 1/0/1 and
GigabitEthernet 1/0/2, and disable the spanning tree feature. Configure the two ports as trunk ports,
and assign them to VLAN 1 and VLAN 2.
[DeviceB] interface gigabitethernet 1/0/1
[DeviceB-GigabitEthernet1/0/1] undo link-delay
[DeviceB-GigabitEthernet1/0/1] undo stp enable
[DeviceB-GigabitEthernet1/0/1] port link-type trunk
[DeviceB-GigabitEthernet1/0/1] port trunk permit vlan 1 2
[DeviceB-GigabitEthernet1/0/1] quit
[DeviceB] interface gigabitethernet 1/0/2
[DeviceB-GigabitEthernet1/0/2] undo link-delay
[DeviceB-GigabitEthernet1/0/2] undo stp enable
[DeviceB-GigabitEthernet1/0/2] port link-type trunk
[DeviceB-GigabitEthernet1/0/2] port trunk permit vlan 1 2
[DeviceB-GigabitEthernet1/0/2] quit
# Cancel the physical state change suppression interval setting on GigabitEthernet 1/0/3, and disable
the spanning tree feature. Configure the port as a trunk port, and assign it to VLAN 2.
[DeviceB] interface gigabitethernet 1/0/3
[DeviceB-GigabitEthernet1/0/3] undo link-delay
[DeviceB-GigabitEthernet1/0/3] undo stp enable
[DeviceB-GigabitEthernet1/0/3] port link-type trunk
[DeviceB-GigabitEthernet1/0/3] port trunk permit vlan 2
[DeviceB-GigabitEthernet1/0/3] quit
# Cancel the physical state change suppression interval setting on GigabitEthernet 1/0/4, and disable
the spanning tree feature. Configure the port as a trunk port, and assign it to VLAN 1.
[DeviceB] interface gigabitethernet 1/0/4
[DeviceB-GigabitEthernet1/0/4] undo link-delay
[DeviceB-GigabitEthernet1/0/4] undo stp enable
[DeviceB-GigabitEthernet1/0/4] port link-type trunk
[DeviceB-GigabitEthernet1/0/4] port trunk permit vlan 1
[DeviceB-GigabitEthernet1/0/4] quit
# Create RRPP domain 1. Configure VLAN 100 as the primary control VLAN of RRPP domain 1, and
configure the VLAN mapped to MSTI 1 as the protected VLAN of RRPP domain 1.
[DeviceB] rrpp domain 1
[DeviceB-rrpp-domain1] control-vlan 100
[DeviceB-rrpp-domain1] protected-vlan reference-instance 1
# Configure Device B as a transit node of primary ring 1 in RRPP domain 1, with GigabitEthernet 1/0/1
as the primary port and GigabitEthernet 1/0/2 as the secondary port, and enable ring 1.