BayTech MRP units 2012 - Manual (Page 22)

Page
22
OUTLET CONTROLLER STATUS SCREEN
MRP-10 Series
(C) 2008 BayTech
F1.12
True RMS Voltage
True RMS Current
Internal Temperature
Unit ID: MRP-10
Total kW-h: 8731
-------------------------------------------------------------------------------
| Circuit | True RMS | Peak RMS | True RMS | Average | Volt- |
| Group | Current | Current | Voltage | Power | Amps |
-------------------------------------------------------------------------------
| Circuit M1 | 0.0 Amps | 0.0 Amps | 196.7 Volts | 0 Watts | 4 VA |
| Circuit M2 | 0.0 Amps | 0.0 Amps | 200.8 Volts | 0 Watts | 4 VA |
| Circuit M3 | 0.0 Amps | 0.0 Amps | 200.3 Volts | 0 Watts | 4 VA |
| Circuit M4 | 0.0 Amps | 0.0 Amps | 199.4 Volts | 0 Watts | 4 VA |
| Circuit M5 | 0.0 Amps | 0.0 Amps | 198.6 Volts | 0 Watts | 4 VA |
| Circuit M6 | 0.0 Amps | 0.0 Amps | 199.6 Volts | 0 Watts | 4 VA |
-------------------------------------------------------------------------------
Int. Temp: 115.7 F Ext. 1: 74.7 F : 52.7% RH Ext. 2: 72.0 F
1)...MOD 1 Outlet 1 : On 2)...MOD 1 Outlet 2 : On
3)...MOD 1 Outlet 3 : On 4)...MOD 1 Outlet 4 : On
5)...MOD 2 Outlet 1 : On 6)...MOD 2 Outlet 2 : On
7)...MOD 2 Outlet 3 : On 8)...MOD 2 Outlet 4 : On
9)...MOD 3 Outlet 1 : On 10)...MOD 3 Outlet 2 : On
11)...MOD 3 Outlet 3 : On 12)...MOD 3 Outlet 4 : On
13)...MOD 4 Outlet 1 : On 14)...MOD 4 Outlet 2 : On
15)...MOD 4 Outlet 3 : On 16)...MOD 4 Outlet 4 : On
17)...MOD 5 Outlet 1 : On 18)...MOD 5 Outlet 2 : On
19)...MOD 5 Outlet 3 : On 20)...MOD 5 Outlet 4 : On
21)...MOD 6 Outlet 1 : On 22)...MOD 6 Outlet 2 : On
23)...MOD 6 Outlet 3 : On 24)...MOD 6 Outlet 4 : On
Type Help for a list of commands
MRP-10>
Type “Help” at the prompt to display a list of commands to change the outlet state, outlet
configuration, and internal sensor measurements.
NOTE: Int. Temp = unit internal temperature. Ext = external temperature probe. Two
environmental ports are available. Temperature reads in Fahrenheit or Celsius.
RH = Relative humidity.
NOTE: The user will see only those outlets assigned to them by the admin user.
NOTE: The first three letters in the prompt designate a class of units with a sub-class
of numbers. Classes = (MDP, MMP, MRP, MSP); i.e. MRP10 is the model number.
The Outlet Controller displays the measured circuit True RMS and Peak RMS current values; True RMS
Voltage; Average Power, Voltage/Amps; Internal and External temperature and Humidity with attached
probes; along with Open/Close external Switch probes. Also displays the outlet status. At the prompt type
“Help” for outlet command and other menus
.