BINDER KB 23 User Manual

Operating manual, Apt.line™ kb (e3.1), kb (e5.1) cooling incubators, With compressor technology and program control

This manual is related to the following products:

KB 53 KB 115 KB 240 KB 400 KB 720 FP 53 FP 115 FP 240 FP 400 FP 720

Table of contents

Document Outline

EC – declaration of conformity
Product registration
1. Safety
- 1.1 Legal considerations
- 1.2 Structure of the safety instructions
- 1.3 Localization / position of safety labels on the unit
- 1.4 Type plate
- 1.5 General safety instructions on installing and operating the cooling incubator
- 1.6 Intended use
2. Unit description
- 2.1 Unit overview
- 2.2 Control panel
- 2.3 KB (E5.1) 240 / 400 / 720: Lateral control panel at the right side (option)
- 2.4 KB (E5.1) 240 / 400 / 720: Lateral control panel at the left side (option)
- 2.5 Unit rear
3. Completeness of delivery, transportation, storage, and installation
- 3.1 Unpacking, and checking equipment and completeness of delivery
- 3.2 Guidelines for safe lifting and transportation
- 3.3 Storage
- 3.4 Location of installation and ambient conditions
4. Installation of the equipment
- 4.1 Spacers for wall distance (KB 240, 400, 720)
- 4.2 Electrical connection
5. Start up
- 5.1 Settings at the RD3 program controller
- 5.2 General indications
6. Fixed value entry mode
7. Week program editor
- 7.1 Program table template for Week program Editor
8. Program editor
- 8.1 Selecting between set-point ramp and set-point step
- 8.2 Set-point entry for program operation
- 8.3 Program table template for Program Editor
- 8.4 Deleting a program section
9. Program start level
10. User level
11. Programming example of the Week Program Editor
- 11.1 Desired time function
- 11.2 Proceeding overview
- 11.3 Proceeding in detail
12. Programming example of the Program Editor
- 12.1 Desired time function
- 12.2 Proceeding overview
- 12.3 Proceeding in detail
13. Performance in case of failures
- 13.1 Performance after a power failure
- 13.2 Alarm messages
14. Temperature safety devices
- 14.1 Over temperature protective device (class 1)
- 14.2 Safety controller (temperature safety device class 3.1)
- 14.3 Temperature safety device class 3.3 (option)
  - 14.3.1 Temperature safety device class 3.1
  - 14.3.2 Temperature safety device class 3.2
15. Defrosting during refrigerating operation
16. Options
- 16.1 Communication software APT-COM™ 3 DataControlSystem (option)
- 16.2 Ethernet interface (option for KB 240, 400, 720)
- 16.3 Data logger kit (option)
- 16.4 Analog output for temperature (option)
- 16.5 Water protected internal socket (option from size 53 on – not for KB-UL)
- 16.6 Zero-voltage relay outputs via operation lines (option from size 53 on)
- 16.7 Additional flexible Pt 100 temperature sensor (option for KB 53, 115)
- 16.8 Additional flexible Pt 100 temperature sensor (option for KB 240, 400, 720)
17. Maintenance, cleaning, and service
- 17.1 Maintenance intervals, service
- 17.2 Cleaning and decontamination
  - 17.2.1 Cleaning
  - 17.2.2 Decontamination
- 17.3 Sending the unit back to BINDER GmbH
18. Disposal
- 18.1 Disposal of the transport packing
- 18.2 Decommissioning
- 18.3 Disposal of the unit in the Federal Republic of Germany
- 18.4 Disposal of the unit in the member states of the EC except for the Federal Republic of Germany
- 18.5 Disposal of the unit in non-member states of the EC
19. Troubleshooting
20. Technical description
- 20.1 Factory calibration and adjustment
- 20.2 Over current protection
- 20.3 Definition of usable volume
- 20.4 KB (E3.1) technical data
- 20.5 KB (E5.1) technical data
- 20.6 Equipment and Options
- 20.7 Spare parts and accessories
- 20.8 Dimensions KB 240
- 20.9 Dimensions KB 400
- 20.10 Dimensions KB 720
21. Contamination clearance certificate
- 21.1 For units located outside North America and Central America
- 21.2 For units in North America and Central America
Word-Lesezeichen
- OLE_LINK5
- OLE_LINK6
- OLE_LINK20
- OLE_LINK8
- OLE_LINK7
Leere Seite