Futaba 14SG 2.4GHz - Manual (Page 53)

52
ŏ 6HOHFW WKH IXQFWLRQ QDPH
DQG UHWXUQ WR WKH 6\VWHP
PHQX E\ WRXFKLQJ WKH
R T N E X W W R Q
2 U W K H
H O M E / E X I T E X W W R Q L V
SXVKHG
Mode and switch selection
$FFHVV WKH VHWXS VFUHHQ SDJH VKRZQ
EHORZ E\ WRXFKLQJ WKH 6 EXWWRQ WKUHH WLPHV
0RYH WKH FXUVRU WR WKH >$&7@ RU >&+@
LWHP DQG WRXFK WKH 571 EXWWRQ WR VZLWFK WR
WKH GDWD LQSXW PRGH
6HOHFW WKH PRGH E\ VFUROOLQJ WKH WRXFK
VHQVRU 7KH GLVSOD\ EOLQNV 7RXFK WKH 571
EXWWRQ WR FKDQJH WKH PRGH 7R WHUPLQDWH
WKH PRGH FKDQJH WRXFK WKH 6 EXWWRQ
$&7 (QDEOH RSHUDWLRQ E\ FKDQJLQJ WR >2))@
RU >21@
&+ :KHQ WKH VWXGHQW XVHV WKH 76*
70= 7= 7)* RU ); VHOHFW >&+@
2WKHUZLVH VHOHFW >&+@
,I FKDQJLQJ WKH WUDLQHU VZLWFK
0RYH WKH FXUVRU WR WKH >6:@ LWHP DQG WRXFK
WKH 571 EXWWRQ WR DFFHVV WKH VZLWFK VHWXS
VFUHHQ
6HH 6ZLWFK VHOHFWLRQ PHWKRG DW WKH HQG RI
WKLV PDQXDO IRU VHOHFWLRQ PHWKRG GHWDLOV
6: 6HOHFW WKH GHVLUHG VZLWFK
,QLWLDO VHWWLQJ 6+
*The switch mode can also be selected when setting the ON
position on the switch setup screen. When [ALTERNATE
OFF] is selected, normal ON/OFF operation is performed.
When [ALTERNATE ON] is selected, the trainer function
is alternately turned on and off each time the switch is
operated. This allows alternate ON/OFF switching even
when a momentary switch (SH) is used.
ŏ 6HOHFW >75$,1(5@ LQ WKH 6\VWHP PHQX DQG HQWHU WKH
VHWXS VFUHHQ VKRZQ EHORZ E\ WRXFKLQJ WKH 571
EXWWRQ
Note: The trainer function won’t be turned
on unless the Instructor's transmitter receives
signals from the student's transmitter. Be
sure to confirm this after connecting your
trainer cable.
Operating mode selection
6HWXS VFUHHQ SDJH
0RYH WKH FXUVRU WR WKH >02'(@ LWHP RI WKH
FKDQQHO \RX ZDQW WR FKDQJH DQG WRXFK WKH
571 EXWWRQ WR VZLWFK WR WKH GDWD LQSXW PRGH
6HOHFW WKH PRGH E\ VFUROOLQJ WKH WRXFK
VHQVRU 7KH GLVSOD\ EOLQNV 7RXFK WKH 571
EXWWRQ WR FKDQJH WKH PRGH 7R WHUPLQDWH
WKH PRGH FKDQJH WRXFK WKH 6 EXWWRQ
02'( 6HOHFW WKH GHVLUHG RSHUDWLRQ PRGH
IRU HDFK FKDQQHO
NORM: The model is controlled by signals from the student
transmitter.
MIX mode: The model is controlled by signals from the
instructor and student transmitters. (Reset the student's
model data to the default condition.)
FUNC mode (function mode): The model is controlled by
signals from the student transmitter with the instructor 's
setting. (Reset the student's model data to the default
condition.)
OFF: Only the instructor side operates.
Adjusting the student's rate.
*This can be adjusted for students who may need lower rates
than a more experienced student.
6FUROOLQJ
ŏ 0RYLQJ FXUVRU
ŏ 6HOHFWLQJ PRGH
ŏ $GMXVWLQJ YDOXH
ŏ 7R QH[W SDJH