Futaba 14SG 2.4GHz - Manual (Page 47)

46
1. Model addition and selection
Initially, the T14SG assigns the first model to
model-01 in the transmitter. To add new models
or to select a model already programmed, use the
Model Select function of the Linkage Menu.
This is convenient when selecting a model
after entering the model's names in advance. The
T14SG is capable of storing up to 30 models in the
transmitter's internal memory. Additional models
can also be stored in an optional SD card.
The currently selected model is displayed in
the middle of the screen. Before flying and before
changing any settings, always confirm the model
name.
When a new model is added, the Model Type select
screen and system mode setup screen automatically
appear. Change, or check that they match the swash
type and receiver type of the model used.
When a new model is added, you will need to re-
link the receiver.
2. Model type and swash type selection
If a different model type is already selected,
select helicopter with the Model Type function of
the Linkage Menu, and then select the swash type
matched to the helicopter.
*The Model Type function automatically selects the
appropriate output channels, control functions, and mixing
Helicopter basic setting procedure
This section outlines examples of use of the helicopter functions of the T14SG. Adjust the actual values,
etc. to match the fuselage used.
functions for the chosen model type. Six swash types are
available for helicopters.
*For a description of the swash type selection, refer to the
MODEL TYPE function.
3. Flight condition addition
7KH WUDQVPLWWHU RIIHUV XS WR ¿YH ÀLJKW FRnditions
per model.
The Condition Select function automatically
DOORFDWHV ¿YH FRQGLWLRQV IRU KHOLFRSWHUV
,QLWLDO VHWWLQJ
ŏ 1250$/
ŏ ,'/( 83 6:(
ŏ ,'/( 83 6:(
ŏ ,'/( 83 6:)
ŏ+2/' +ROG VZLWFK LV QRW DVVLJQHG LQLWLDOO\
Note: Since you may accidentally activate
a condition that not previously setup during
ÁLJKW ZKLFK FRXOG FDXVH D FUDVK ZH VXJJHVW
deleting conditions that are not used.
*For a description of the condition deletion, refer to the
Condition Select function.
The NORMAL condition is always on, and
remains on until other conditions are activated by
switches.
The priority is throttle hold/idle up 3/idle up 2/
idle up 1/normal. Throttle hold has the highest
priority.
The Condition Delay can be programmed for
each channel and condition. The Condition Delay
is used to change the servo throw smoothly when
switching conditions.
*HQHUDO ÀLJKW FRQGLWLRQ VHWWLQJ H[DPSOH
ŏ 1RUPDO 8VH LQLWLDO VHWWLQJ FRQGLWLRQVRSHUDWH
ZKHQ VZLWFK 2))
8VH IURP HQJLQH VWDUWLQJ WR KRYHULQJ
ŏ ,GOH XS 2SHUDWH DW 6:( FHQWHU
8VH LQ VWDOO WXUQ ORRS DQG RWKHU PDQHXYHUV
ŏ ,GOH XS 2SHUDWH DW 6:( IRUZDUG VLGH
8VH LQ UROOV
ŏ 7KURWWOH KROG 2SHUDWH DW 6:* IRUZDUG VLGH
8VH LQ DXWR URWDWLRQ