Futaba 14SG 2.4GHz - Manual (Page 119)

118
ŏ 6HOHFW WKH IXQFWLRQ QDPH
and return to the Model
menu by touching the
R T N b u t t o n .
O r t h e
H O M E / E X I T b u t t o n i s
pushed.
This function adjusts the throttle curve for
optimum engine speed from throttle stick input.
*When throttle curve is set to ON when there is no throttle
function; this curve acts as the motor function.
NOTE: If this throttle curve function is activated,
you can not use the THR-EXP function within
the DUAL RATE function simultaneously.
ŏ 6HOHFW >7+5 &859(@ DW WKH 0RGHO PHQX
and access the setup screen shown
below by touching the RTN button.
ŏ&XUYH UDWH
Scrolling
ŏ 0RYLQJ FXUVRU
ŏ 6HOHFWLQJ PRGH
ŏ $GMXVWLQJ YDOXH
ŏ 7R QH[W SDJH
THR CURVE >&RUUHVSRQGLQJ PRGHO W\SH@ $LUSODQHJOLGHU JHQHUDO
Setting method
Ɣ$FWLYDWH WKH IXQFWLRQ
0RYH WKH FXUVRU WR WKH >$&7@ LWHP DQG WRXFK
the RTN button to switch to the data input
mode.
Select the ON mode by scrolling the touch
sensor.
*The display blinks.
T o u c h t h e R T N b u t t o n t o a c t i v a t e t h e
function and return to the cursor mode.
ƔSRLQW FXUYH VHWWLQJ
>&XUYH UDWH VHWWLQJ@
1. Move the cursor to the curve rate setting
LWHP \RX ZDQW WR DGMXVW DQG WRXFK WKH 571
button to switch to the data input mode.
$GMXVW WKH UDWH E\ VFUROOLQJ WKH WRXFK VHQVRU
,QLWLDO YDOXH
$GMXVWPHQW UDQJH a
*When the RTN button is touched for one second, the rate is
reset to the initial value.)
7RXFK WKH 571 EXWWRQ WR HQG WKH DGMXVWPHQW
and return to the cursor mode.
2. Repeat this procedure for each point.
>0RYLQJ FXUYH SRLQW@
1. Move the cursor to the curve point setting
LWHP \RX ZDQW WR DGMXVW DQG WRXFK WKH 571
button to switch to the data input mode.
$GMXVW WKH FXUYH SRLQW E\ VFUROOLQJ WKH WRXFK
sensor.
,QLWLDO YDOXH 3 3 3 3
3
$GMXVWPHQW UDQJH 8S WR LQ IURQW RI WKH
DGMRLQLQJ SRLQW
*When the RTN button is touched for one second, the curve
position is reset to the initial value.)
7RXFK WKH 571 EXWWRQ WR HQG WKH DGMXVWPHQW
and return to the cursor mode.
2. Repeat this procedure for each point.
>'HOHWLQJUHWXUQLQJ FXUYH SRLQW@
Move the cursor to the curve point setting
LWHP \RX ZDQW WR GHOHWHUHWXUQ DQG WRXFK
the RTN button for one second.
ŏ&XUYH SRLQW