Futaba 14SG 2.4GHz - Manual (Page 126)

125
ŏ 6HOHFW WKH IXQFWLRQ QDPH
and return to the Model
menu by touching the
R T N b u t t o n .
O r t h e
H O M E / E X I T b u t t o n i s
pushed.
RUD to AIL >&RUUHVSRQGLQJ PRGHO W\SH@ $LUSODQHJOLGHU JHQHUDO
This function is used when you want to mix
the ailerons with rudder input. It is used when
rudder is applied during roll maneuvers such
as, knife edge flight. It can be used to turn or
bank scale models, large models, etc. like a full-
size aircraft.
ŏ 0L[LQJ GXULQJ IOLJKW FDQ EH WXUQHG 212)) E\
VHWWLQJ D VZLWFK $OZD\V 21 DW >@ VHWWLQJ
ŏ /LQNLQJ FDQ EH VHW /LQN WKLV PL[ WR RWKHU PL[HV
ŏ 7KH PL[LQJ UDWH FDQ DOVR EH DGMXVWHG
ŏ $ SRLQW FXUYH FDQ EH VHW DW DLUSODQH PRGHO W\SH
ŏ 6HOHFW >58' WR $,/@ DW WKH 0RGHO
menu and access the setup screen
shown below by touching the RTN
button.
*The display screen is an example.
The actual screen depends on the
model type.
Scrolling
ŏ 0RYLQJ FXUVRU
ŏ 6HOHFWLQJ PRGH
ŏ $GMXVWLQJ YDOXH
ŏ 7R QH[W SDJH
Setting method
Ɣ$FWLYDWH WKH IXQFWLRQ
0RYH WKH FXUVRU WR WKH >$&7@ LWHP DQG WRXFK
the RTN button to switch to the data input
PRGH 6HOHFW WKH $&7 PRGH E\ VFUROOLQJ WKH
touch sensor.
*The display blinks.
T o u c h t h e R T N b u t t o n t o a c t i v a t e t h e
IXQFWLRQ DQG UHWXUQ WR WKH FXUVRU PRGH 21
LV GLVSOD\HG
When setting a switch, move the cursor to
WKH >6:@ LWHP DQG WRXFK WKH 571 EXWWRQ WR
call the selection screen. Select the switch
DQG VHW LWV 21 GLUHFWLRQ $OZD\V 21 DW
VHWWLQJ
*For a description of the switch selection method, see the
description at the back of this manual.
Ɣ0L[LQJ UDWH DGMXVWPHQW JOLGHU
Move the cursor to the left or right item
and touch the RTN button to switch to the
GDWD LQSXW PRGH $GMXVW WKH PL[LQJ UDWH
independently by scrolling the touch sensor.
,QLWLDO YDOXH
$GMXVWPHQW UDQJH a
*When the RTN button is touched for one second, the rate is
reset to the initial value.)
7RXFK WKH 571 EXWWRQ WR HQG WKH DGMXVWPHQW
and return to the cursor mode.
Ɣ/LQN PRGH VHWWLQJ
To activate the link mixing, move the cursor
WR WKH >/,1.@ LWHP DQG WRXFK WKH 571 EXWWRQ
to switch to the data input mode. Select the
ON mode by scrolling the touch sensor.
*The display blinks.
Touch the RTN button to set the link mode
and return to the cursor mode.
(Glider: Currently selected condition name)