Futaba 14SG 2.4GHz - Manual (Page 143)

142
ŏ 6HOHFW WKH IXQFWLRQ QDPH
and return to the Model
menu by touching the
R T N b u t t o n .
O r t h e
H O M E / E X I T b u t t o n i s
pushed.
MOTOR >&RUUHVSRQGLQJ PRGHO W\SH@ $LUSODQHJOLGHU JHQHUDO
This function lets you set the speed when the
motor of an F5B or other EP glider is started via
a switch. The operation speed can be set for two
ranges, slow speed flight and high speed flight
(Speed 1/Speed 2). This function can also be
operated as a safety function by programming it to
a switch.
ŏ 7KH ,Q VLGH DQG 2XW VLGH RSHUDWLQJ VSHHGV FDQ
EH DGMXVWHG LQGHSHQGHQWO\ LQ UDQJHV 6SHHG
6SHHG
ŏ 7KH ERXQGDU\ EHWZHHQ WKH UDQJHV FDQ EH VHW
)URP 6SHHG WR 6SHHG
ŏ 7KH RSHUDWLRQDO VSHHG FDQ RQO\ EH DFWLYDWHG DW
WKH LQLWLDO RSHUDWLRQ +RZHYHU RSHUDWLRQ FDQ EH
UHSHDWHG E\ VHWWLQJ WKH VZLWFK WR 2)) EHIRUH WKH
RSHUDWLRQ LV ÀQLVKHG :KHQ \RX ZDQW WR UHVHW RQH
WLPH RSHUDWLRQ VHW WKH $&7,1+ LWHP WR >,1+@ DQG
WKHQ UHVHW LW WR >21@
ŏ 7KH PRWRU FKDQQHO LV FRQWUROOHG E\ 6:* *OLGHU
,QLWLDO VHWWLQJ :KHQ FKDQJLQJ WKH VZLWFK RU VWLFN
ZKLFK FRQWUROV WKH PRWRU ÀUVW FKDQJH )XQFWLRQ RI
the Linkage menu.
ŏ ,I WKH 0RGHO 7\SH VHOHFWHG LV $LUSODQH WKH 02725
IXQFWLRQ LV FKDQJHG IURP ,1+ WR 21 DQG LW LV QRW
assigned to another channel, the changes from
the throttle channel to the motor channel are
enabled.
Note: Initial setting does not assign a motor
channel according to the model type. Prior to
DVVLJQLQJ WKH PRWRU FKDQQHO ÀQG DQ XQXVHG
channel. Then, use the Function menu of the
Linkage menu.
Set [Control] to the switch you want to use
and [Trim] to [--].
Note: When using this function, always check
the initial operation with the propeller
removed.
ŏ 6HOHFW >02725@ DW WKH 0RGHO PHQX
and access the setup screen shown
below by touching the RTN button.
Scrolling
ŏ 0RYLQJ FXUVRU
ŏ 6HOHFWLQJ PRGH
ŏ $GMXVWLQJ YDOXH
ŏ 7R QH[W SDJH
Setting method
Ɣ $FWLYDWH WKH IXQFWLRQ
When using this function, move the cursor to
WKH >$&7,1+@ LWHP DQG WRXFK WKH 571 EXWWRQ
to switch to the data input mode. Select the
>$&7@ E\ VFUROOLQJ WKH WRXFK VHQVRU DQG WRXFK
the RTN button.
:KHQ VHOHFWLQJ WKH 212)) VZLWFK PRYH WKH
cursor to the switch item and touch the RTN
button to access the selection screen. Select
WKH VZLWFK DQG VHW LWV 21 GLUHFWLRQ $OZD\V
21 DW VHWWLQJ
*For a description of the switch selection method, see the
description at the back of this manual.
Ɣ 0RWRU RII SRVLWLRQ VHWWLQJ
0RYH WKH FXUVRU WR WKH >02725 2))@ LWHP
and touch the RTN button for one second
ZKHQ WKH PRWRU IXQFWLRQ VZLWFK 6* HWF LV
LQ WKH PRWRU 2)) SRVLWLRQ \RX ZDQW WR VHW 7KH
direction of the motor switch is memorized.
7KH VFUHHQ JUDSK GLVSOD\ 2)) GLUHFWLRQ DOVR
changes.
Note:
ŏ )LUVW GHFLGH WKH PRWRU 2)) GLUHFWLRQ DQG WKHQ
set the speed. When you want to reset the
motor OFF direction, also reset the speed.
ŏ :H UHFRPPHQG WKDW 0RWRU 2)) EH VHW LQ
combination with F/S.
ŏ 6HW WKH EDVLF RSHUDWLRQ GLUHFWLRQ ZLWK WKH
Reverse function to match the ESC used.
ŏ $OZD\V VHW WKH 0RWRU 2)) SRVLWLRQ