Futaba 14SG 2.4GHz - Manual (Page 133)

132
Setting method
Ɣ$FWLYDWH WKH IXQFWLRQ
0RYH WKH FXUVRU WR WKH >$&7@ LWHP DQG WRXFK
the RTN button to switch to the data input
PRGH 6HOHFW WKH $&7 PRGH E\ VFUROOLQJ WKH
touch sensor.
*The display blinks.
T o u c h t h e R T N b u t t o n t o a c t i v a t e t h e
IXQFWLRQ DQG UHWXUQ WR WKH FXUVRU PRGH 21
LV GLVSOD\HG
When setting a switch, move the cursor to
WKH >6:@ LWHP DQG WRXFK WKH 571 EXWWRQ WR
call the selection screen. Select the switch
DQG VHW LWV 21 GLUHFWLRQ $OZD\V 21 DW
VHWWLQJ
*For a description of the switch selection method, see the
description at the back of this manual.
Ɣ5DWH DGMXVWPHQW
Move the cursor to the aileron, flap or
elevator rate item and touch the RTN button
WR VZLWFK WR WKH GDWD LQSXW PRGH $GMXVW WKH
rate independently by scrolling the touch
sensor.
,QLWLDO YDOXH
$GMXVWPHQW UDQJH a (OHYDWRU
a
*When the RTN button is touched for one second, the rate is
reset to the initial value.)
7RXFK WKH 571 EXWWRQ WR HQG WKH DGMXVWPHQW
and return to the cursor mode.
Ɣ (OHYDWRU FRPSHQVDWLRQ FXUYH DGMXVWPHQW
2XWSXW < 3RVLWLRQ ;
Offset point )L[HG )L[HG RIIVHW
SRVLWLRQ
,QWHUPHGLDWH SRLQW Settable Settable
(QG SRLQW Settable )L[HG
* The range where mixing does not work close to the neutral
position of the elevator stick can be adjusted. (Glider only)
*When offset is set, the curve is initialized.
Ɣ5HIHUHQFH SRLQW DGMXVWPHQW
0RYH WKH FXUVRU WR WKH >2))6(7@ LWHP DQG
hold the airbrake stick to the desired position
and then touch the RTN button for one
second to set the butterfly operational
reference point.
,QLWLDO YDOXH XSSHU VLGH
$GMXVWPHQW UDQJH a
Ɣ6HUYR VSHHG VHWWLQJ
Move the cursor to the aileron, flap or
elevator speed item and touch the RTN
button to switch to the data input mode.
$GMXVW WKH UDWH E\ VFUROOLQJ WKH WRXFK VHQVRU
,QLWLDO YDOXH
$GMXVWPHQW UDQJH a PD[LPXP GHOD\
*When the RTN button is touched for one second, the rate is
reset to the initial value.)
T o u c h t h e R T N b u t t o n t o a c t i v a t e t h e
function and return to the cursor mode.