Futaba 14SG 2.4GHz - Manual (Page 118)

117
ŏ 6HOHFW WKH IXQFWLRQ QDPH
and return to the Model
menu by touching the
R T N b u t t o n .
O r t h e
H O M E / E X I T b u t t o n i s
pushed.
This function adjusts the pitch curve for VPP
(Variable Pitch Propeller) airplane.
*Up to 3 conditions can be set.
7KH SULRULW\ LQFUHDVHV LQ FRQGLWLRQ ĺĺ RUGHU
N O T E : W h e n V P P i s n o t a s s i g n e d t o a n y
channel, the pitch curve is not displayed in
the model menu. In this case, assign VPP to
any channel on the function screen.
ŏ 6HOHFW >3,7 &859(@ DW WKH 0RGHO PHQX
and access the setup screen shown
below by touching the RTN button.
ŏ&XUYH UDWH
Scrolling
ŏ 0RYLQJ FXUVRU
ŏ 6HOHFWLQJ PRGH
ŏ $GMXVWLQJ YDOXH
ŏ 7R QH[W SDJH
PIT CURVE >&RUUHVSRQGLQJ PRGHO W\SH@ $LUSODQH JHQHUDO
Setting method
Ɣ933 FRQGLWLRQ VHOHFWLRQ
1. Move the cursor to the # button at the top
right side of the screen and touch the RTN
button to switch to the data input mode.
6HOHFW WKH 933 FRQGLWLRQ E\ VFUROOLQJ WKH
touch sensor.
*The display blinks.
Touch the RTN button to call the setting
screen and return to the cursor mode.
2. Move the cursor to the switch item and
touch the RTN button to access the selection
screen. Select the switch and set its ON
direction.
*For a description of the switch selection method, see the
description at the back of this manual.
6HW WKH 933 FRQGLWLRQ DQG VZLWFK
*The VPP conditions can also be checked in the HOME
screen.
ƔSRLQW FXUYH VHWWLQJ
>&XUYH UDWH VHWWLQJ@
1. Move the cursor to the curve rate setting
LWHP \RX ZDQW WR DGMXVW DQG WRXFK WKH 571
button to switch to the data input mode.
$GMXVW WKH UDWH E\ VFUROOLQJ WKH WRXFK VHQVRU
,QLWLDO YDOXH
$GMXVWPHQW UDQJH a
*When the RTN button is touched for one second, the rate is
reset to the initial value.
7RXFK WKH 571 EXWWRQ WR HQG WKH DGMXVWPHQW
and return to the cursor mode.
2. Repeat this procedure for each point.
>0RYLQJ FXUYH SRLQW@
1. Move the cursor to the curve point setting
LWHP \RX ZDQW WR DGMXVW DQG WRXFK WKH 571
button to switch to the data input mode.
$GMXVW WKH FXUYH SRLQW E\ VFUROOLQJ WKH WRXFK
sensor.
,QLWLDO YDOXH 3 3 3 3
3
$GMXVWPHQW UDQJH 8S WR LQ IURQW RI WKH
DGMRLQLQJ SRLQW
*When the RTN button is touched for one second, the curve
position is reset to the initial value.)
7RXFK WKH 571 EXWWRQ WR HQG WKH DGMXVWPHQW
and return to the cursor mode.
2. Repeat this procedure for each point.
>'HOHWLQJUHWXUQLQJ FXUYH SRLQW@
Move the cursor to the curve point setting
LWHP \RX ZDQW WR GHOHWHUHWXUQ DQG WRXFK
the RTN button for one second.
ŏ&XUYH SRLQW