Futaba 14SG 2.4GHz - Manual (Page 49)

48
function from the Model Menu, and set the curve
for each condition. (At initial setting, this function
is in the "INH" state. To use it, set it to the "ON"
state.)
6HWWLQJ H[DPSOH!
Activate the mixing curve of each condition with
the condition select switch.
$ FXUYH VHWWLQJ H[DPSOH LV VKRZQ EHORZ
ŏ3LWFK WR 58' PL[LQJ FXUYH 1RUPDO
8VH WKH KRYHULQJ V\VWHP DQG VHW WKLV FXUYH WR
PDWFK WDNH RII DQG ODQGLQJ DQG YHUWLFDO FOLPE DW D
FRQVWDQW VSHHG
ŏ3LWFK WR 58' PL[LQJ ,GOH XS
8VH WKLV FXUYH LQ VWDOO WXUQ ORRS DQG DGMXVW LW VR WKH
IXVHODJH LV IDFLQJ VWUDLJKW DKHDG ZKHQ KHDGLQJ
LQWR WKH ZLQG
ŏ3LWFK WR 58' PL[LQJ +ROG
7KLV IXQFWLRQ LV VHW VR WKDW WKH IXVHODJH LV IDFLQJ
VWUDLJKW DKHDG DW VWUDLJKW OLQH DXWR URWDWLRQ 7KH
SLWFK RI WKH WDLO URWRU EHFRPHV QHDUO\ º
9. Throttle hold setting
*If throttle hold is necessary, please refer to the THR HOLD
function.
10. Throttle cut setting
Throttle cut provides an easy way to stop the
HQJLQH E\ ÀLSSLQJ D VZLWFK ZLWK WKH WKURWWOH VWLFN
at idle. The action is not functional at high throttle
to avoid accidental dead sticks. The switch’s
location and direction must be chosen, as it defaults
to NULL.
*With throttle stick at idle, adjust the cut position until the
engine consistently shuts off, but throttle linkage is not
binding.
6ZDVK 0L[ FRUUHFWV DLOHURQ HOHYDWRU DQG
pitch interaction
The swash mix function is used to correct the
swash plate in the aileron (Left/Right Cyclic)
and elevator (Forward/Aft Cyclic) direction
corresponding to each operation of each condition.
6. D/R function
D/R function is used to adjust the throw and
operation curve of aileron, elevator and rudder for
each condition.
*For throttle and pitch curve settings, refer to the afore-
mentioned "Throttle/Pitch curve setting"
7KLV LV QRUPDOO\ XVHG DIWHU (QG 3RLQW KDV GH¿QHG
the maximum throw directions.
*\UR VHQVLWLYLW\ DQG PRGH VZLWFKLQJ
The gyro sensitivity and mode switching
function is utilized to adjust the gyro mixing of the
model, and can be set for each condition.
ŏ 1RUPDO FRQGLWLRQ KRYHULQJ *\UR VHQVLWLYLW\
PD[LPXP
ŏ ,GOH XS ,GOH XS 7KURWWOH KROG *\UR
VHQVLWLYLW\ PLQLPXP
ŏ +RZHYHU GXULQJ DXWR URWDWLRQV ZLWK D WDLO
GULYHQ KHOLFRSWHU WKLV IXQFWLRQ PD\ QRW KDYH
DQ\ HIIHFW RQ WKH KLJK J\UR VHQVLWLYLW\
3LWFK WR 58' PL[LQJ VHWWLQJ
Note: When using a Futaba GY Gyro, or other
heading hold gyro, this Pitch to RUD mixing
should not be used. The reaction torque is
corrected by the gyro. When operating the
gyro in the AVCS mode, the mixed signal will
cause neutral deviation symptoms and the
gyro will not operate normally.
Use this function when you want to suppress
the torque generated by the changes in the pitch
and speed of the main rotor during pitch operation.
Adjust it so that the nose does not swing in the
rudder direction. However, when using a heading
hold gyro like those shown above, do not use Pitch
to rudder mixing.
Activate the Pitch to rudder (Pit -->RUD) mixing