Futaba 14SG 2.4GHz - Manual (Page 145)

144
ŏ 6HOHFW WKH IXQFWLRQ QDPH
and return to the Model
menu by touching the
R T N b u t t o n .
O r t h e
H O M E / E X I T b u t t o n i s
pushed.
RUD to ELE >&RUUHVSRQGLQJ PRGHO W\SH@ $LUSODQH JHQHUDO
This function is used when you want to mix
elevator operation with rudder operation. It is used
to correct undesirable tendencies when rudder is
applied in rolling maneuvers such as, knife edge
ÀLJKW
ŏ 0L[LQJ GXULQJ IOLJKW FDQ EH WXUQHG 212)) E\
VHWWLQJ D VZLWFK $OZD\V 21 DW >@ VHWWLQJ
ŏ /LQN PL[LQJ FDQ EH VHW /LQNV WKLV PL[ WR RWKHU PL[HV
ŏ 6HOHFW >58' WR (/(@ DW WKH 0RGHO
menu and access the setup screen
shown below by touching the RTN
button.
Scrolling
ŏ 0RYLQJ FXUVRU
ŏ 6HOHFWLQJ PRGH
ŏ $GMXVWLQJ YDOXH
ŏ 7R QH[W SDJH
Setting method
Ɣ$FWLYDWH WKH IXQFWLRQ
0RYH WKH FXUVRU WR WKH >$&7@ LWHP DQG WRXFK
the RTN button to switch to the data input
PRGH 6HOHFW WKH $&7 PRGH E\ VFUROOLQJ WKH
touch sensor.
*The display blinks.
T o u c h t h e R T N b u t t o n t o a c t i v a t e t h e
IXQFWLRQ DQG UHWXUQ WR WKH FXUVRU PRGH 21
LV GLVSOD\HG
When selecting a switch, move the cursor to
WKH >6:@ LWHP DQG WRXFK WKH 571 EXWWRQ WR
call the selection screen. Select the switch
DQG VHW LWV 21 GLUHFWLRQ $OZD\V 21 DW
VHWWLQJ
*For a description of the switch selection method, see the
description at the back of this manual.
ƔSRLQW FXUYH VHWWLQJ DLUSODQH
>&XUYH UDWH VHWWLQJ@
1. Move the cursor to the curve rate setting
LWHP OHIW VLGH \RX ZDQW WR DGMXVW DQG WRXFK
the RTN button to switch to the data input
mode.
$GMXVW WKH UDWH E\ VFUROOLQJ WKH WRXFK VHQVRU
$GMXVWPHQW UDQJH a
*When the RTN button is touched for one second, the rate is
reset to the initial value.)
7RXFK WKH 571 EXWWRQ WR HQG WKH DGMXVWPHQW
and return to the cursor mode.
2. Repeat this procedure for each point.
>0RYLQJ FXUYH SRLQW@
1. Move the cursor to the curve point setting
LWHP \RX ZDQW WR DGMXVW DQG WRXFK WKH 571
button to switch to the data input mode.
$GMXVW WKH FXUYH SRLQW E\ VFUROOLQJ WKH WRXFK
sensor.
$GMXVWPHQW UDQJH 8S WR LQ IURQW RI WKH
DGMRLQLQJ SRLQW
*When the RTN button is touched for one second, the curve
position is reset to the initial value.)
7RXFK WKH 571 EXWWRQ WR HQG WKH DGMXVWPHQW
and return to the cursor mode.
2. Repeat this procedure for each point.
>'HOHWLQJUHWXUQLQJ FXUYH SRLQW@
Move the cursor to the curve point setting
LWHP \RX ZDQW WR GHOHWHUHWXUQ DQG WRXFK
the RTN button for one second.
Ɣ/LQN PRGH VHWWLQJ
When selecting the link mixing, move the
FXUVRU WR WKH >/,1.@ LWHP DQG WRXFK WKH 571
button to switch to the data input mode.
Select the ON mode by scrolling the touch
sensor.
*The display blinks.
Touch the RTN button to set the link mode
and return to the cursor mode.