Dynojet 200: Installation Guide - Manual (Page 5)

Motorcycle Dynamometer Installation Guide
iii
L
IST OF
F
IGURES
Figure 1-1: Custom Dyno Room . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3
Figure 1-2: Remove the Ramp Supports and Face . . . . . . . . . . . . . . . . . . . . . 1-5
Figure 1-3: Remove the Tire Carriage from the Crate . . . . . . . . . . . . . . . . . . 1-5
Figure 1-4: Remove the Ramp Bracket from the Crate . . . . . . . . . . . . . . . . . 1-6
Figure 1-5: Hardware Box Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-6
Figure 1-6: Remove the Hood . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-7
Figure 1-7: Loop Strap Placement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-7
Figure 1-8: Remove the Metal Outrigger from the Crate . . . . . . . . . . . . . . . 1-8
Figure 1-9: Secure the Metal Outrigger to the Dyno . . . . . . . . . . . . . . . . . . . 1-8
Figure 1-10: Tire Carriage—Loosen the Clamps and Nut Block . . . . . . . . . . 1-9
Figure 1-11: Tire Carriage—Secure the Hand Crank . . . . . . . . . . . . . . . . . . . 1-9
Figure 1-12: Tire Carriage—Install the Screw Support Bracket . . . . . . . . . . 1-10
Figure 1-13: Attach the Pickup Card to the Bracket . . . . . . . . . . . . . . . . . . . 1-11
Figure 1-14: Align the Pickup Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-11
Figure 1-15: Install the Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-12
Figure 1-16: Secure the Hood to the Dyno . . . . . . . . . . . . . . . . . . . . . . . . . . 1-13
Figure 1-17: Ramp Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-14
Figure 1-18: Electrical Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-15
Figure 2-1: Dynoware EX+ Hardware Stack . . . . . . . . . . . . . . . . . . . . . . . . . .2- 2
Figure 2-2: RPM Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3
Figure 2-3: Dynamometer Input/Output Module . . . . . . . . . . . . . . . . . . . . . 2-4
Figure 2-4: CPU Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-5
Figure 2-5: Connecting the Dynoware EX+ Cables . . . . . . . . . . . . . . . . . . . . 2-6