INFICON 3000 Micro GC Gas Analyzer Operating Manual User Manual
3000 micro gc, Gas analyzer
Table of contents
Document Outline
- Cover Page
- Title Page
- Trademarks
- Disclaimer
- Copyright
- Declaration Of Conformity
- Warranty
- Table Of Contents
- Chapter 1 Introduction
- Chapter 2 Specifications
- 2.1 3000 Micro GC Specifications
- 2.2 Environmental Conditions
- 2.3 Instrument Specifications
- 2.3.1 Sample Inlet Specifications
- 2.3.2 Sample Injector Specifications
- 2.3.3 Column Heater Specification
- 2.3.4 TCD Specifications
- 2.3.5 Repeatability
- 2.3.6 Carrier Gas Specifications
- 2.3.7 Portable 3000 Micro GC Carrier Gas Specifications
- 2.3.8 External Input/Output
- 2.3.9 Portable 3000 Micro GC Onboard Battery
- 2.3.10 Safety and Regulatory Standards
- Chapter 3 Overview
- 3.1 Overview of 3000 Micro GC Instrument and Accessories
- 3.2 3000 Micro GC Chassis
- 3.3 The 3000 Micro GC Module
- 3.4 3000 Micro GC Chassis Components
- 3.5 Sample Conditioners
- 3.6 EZ IQ Chromatography Software
- 3.7 Product Identification
- Chapter 4 Installation
- 4.1 Site Preparation
- 4.2 Instrument Hardware Setup
- 4.3 Instrument Configuration Setup
- 4.4 Chromatography Software Installation
- Chapter 5 Accessory Installation
- 5.1 Sample Conditioners
- 5.1.1 List of Sample Conditioners and IPNs
- 5.1.2 Installing the 10 Micron Sample Inlet Filter
- 5.1.3 Installing the Genie Filter Assembly
- 5.1.4 Installing the Pressure Reducer
- 5.1.5 Installing the Pressure Reducer and Genie Filter Assembly
- 5.1.6 Installing Heated Sample Introduction Accessories
- 5.2 The Remote Connector
- 5.3 Multi-Position Valve Installation and Setup
- 5.1 Sample Conditioners
- Chapter 6 Instrument Setup Through Embedded Web Page Operation
- Chapter 7 Basic EZ IQ Operation
- 7.1 Introduction
- 7.2 Connecting EZ IQ with 3000 Micro GC
- 7.3 Configuring EZ IQ to Use a Valco (VICI) Valve
- 7.4 Navigating EZ IQ
- 7.5 EZ IQ Workflow
- 7.6 Basic Method Development
- 7.7 Run a Sample
- 7.8 Basic Sequencing
- 7.9 Scheduling Runs
- 7.10 Integrating the Chromatogram
- 7.11 Qualify Peaks
- 7.12 Calibration
- 7.13 Generate Standard Reports
- 7.14 EZ IQ Operation to Activate Remote Start/Cancel Function
- 7.15 Apply the Valco Valve Program to EZ IQ Method
- Chapter 8 Instrument Operations
- 8.1 Routine Operation
- 8.2 Remove and Replace a 3000 Micro GC Module
- 8.3 Sample Conditioners
- 8.3.1 Sample Conditioner Connections
- 8.3.1.1 Connections for Sample Inlet Filter (PN G2801-60900), Pressure Reducer (PN G2815A), Pressure Reducer and Genie Filter Assembly (PN G2816A), and Genie Filter Assembly (PN G2817A)
- 8.3.1.2 Connections for the Heated Regulator (PN G2818A-X/G2845A-X/G2857A-X)
- 8.3.1.3 Connections for the Heated Vaporizer (PN G2819A-X/G2846A-X/G2858A-X)
- 8.3.2 Running a Low Pressure, Clean Gas Sample
- 8.3.3 Running a Low Pressure, Liquid/Particulate Containing Gas Sample
- 8.3.4 Running a High Pressure Gas Sample without Liquids/Particulates
- 8.3.5 Running a High Pressure Gas Sample with Liquids/Particulates
- 8.3.6 Running a High Pressure Gas Sample Containing C6+ Components
- 8.3.7 Running a High Pressure Liquid Petroleum Gas Sample
- 8.3.1 Sample Conditioner Connections
- 8.4 Consumable Replacement Procedures
- 8.5 Portable 3000 Micro GC Operation
- Chapter 9 Troubleshooting
- Chapter 10 Service and Technical Support
- Chapter 11 Replacement Parts and Gases
- 11.1 Power Cables and Converters
- 11.2 GC Modules
- 11.3 Sample Accessories and Filters
- 11.4 Checkout Gases
- 11.5 NGA Checkout Gas