Pioneer SC-LX90 - Manual (Page 109)

Controlling the rest of your system 12
109
En
Programming a multi-operation or a
shutdown sequence
Set the remote control operation mode selector switch to
AMP when you want to program this amplifier’s
operations, to
SOURCE when you want to program
operations of other components.
1 While pressing the MULTI OPERATION button,
press SETUP.
The remote LCD display shows
SETUP.
2 Use / to select MULTI OP or SYS OFF from the
menu and press ENTER.
If you selected Multi Operation (
MULTI OP), the LCD on
the remote prompts you for an input source button.
If you selected System Off ( SYS OFF), go to step 4.
3 Press the input source button for the component
that will start the multi-operation, then press ENTER.
For example, if you want to start the sequence by
switching on your DVD player, press
DVD.
4 Use / to select CODE EDT, then press ENTER.
To erase any previously stored multi-operations (or
shutdown sequences) select
CODE ERS above.
5 Use / to select a command in the sequence, then
press ENTER.
If this is the first command in the sequence, select
1ST
CODE. Otherwise, simply choose the next command in
the sequence.
PRES KEY flashes after you press ENTER.
6 If necessary, press the input source button for the
component whose command you want to input.
This is only necessary if the command is for a new
component (input source).
7 Select the button for the command you want to
input.
The following remote control commands can be selected:
• You don’t need to program the amplifier to switch on
or off. This is done automatically.
With Pioneer components, you don’t need to:
• program the power to switch off in a shutdown
sequence (except DVD recorders);
• program the power to switch on if it’s the source
component selected in step 3;
• program a Pioneer TV or monitor to switch on if the
input function (selected in step 2) has video input
terminals;
These take priority in multi operations (not shutdown).
8 Repeat steps 5 to 7 to program a sequence of up to
five commands.
9 When you’re finished, use / to select EXIT from
the menu and press ENTER.
You will return to the remote control Setup menu. Select
* EXIT * again to exit.
Using multi operations
You can start multi operations with the amplifier
switched on, or in standby.
1 Press MULTI OPERATION.
MULTI OP flashes in the display.
2 Press an input source button that has been set up
with a multi operation.
The amplifier switches on (if it was in standby) and the
programmed multi operation is performed automatically.
DVD
AV AMPLIFIER SOURCE MAIN
MULTI
OPERATION
ZONE2 3
DVR1
GALLERY
HOME MEDIA
INPUT SELECT
CD
TUNER iPod HDMI PHONO
CD-R
DVR2 VIDEO1 VIDEO2
BD TV SAT
SACD GALLERY
HOME MEDIA
CD
TUNER iPod HDMI PHONO
CD-R SACD
DVD BD TV SAT
MULTI
OPERATION
DVR1 DVR2 VIDEO1 VIDEO2
AUDIO
PARAMETER
TOP MENU
STATUS
THX
CH LEVEL
MENU
VIDEO
PARAMETER
RETURN
SETUP
INPUT MUTE MUTE
TV CONTROL
ENTER ENTER
SETUP
DVD
AV AMPLIFIER SOURCE MAIN
MULTI
OPERATION
AUDIO VIDEO
ZONE2
SOURCE TV AMP
3
DVR1
GALLERY
HOME MEDIA
INPUT SELECT
CD
TUNER
INPUT MUTE MUTE
VOL
VOL
TV CONTROL
CH
iPod HDMI PHONO
CD-R
DVR2 VIDEO1 VIDEO2
BD TV SAT
SACD
ENTER
AUDIO
PARAMETER
TOP MENU
STATUS
THX
CH LEVEL
MENU
VIDEO
PARAMETER
RETURN
SETUP
STEREO/
F.S.SURR
SIGNAL SEL SLEEP AUDIO DIMMER
SR+
CLR
SBch PHASE iPod CTRL
A.ATT GENRE HDMI OUT
ENTER
MCACC
DISP
CH
AUTO/
DIRECT STANDARD ADV SURR
DVD
AV AMPLIFIER SOURCE MAIN
MULTI
OPERATION
ZONE2 3
DVR1
GALLERY
HOME MEDIA
CD CD-R
DVR2 VIDEO1 VIDEO2
BD TV SAT
SACD
MULTI
OPERATION
SC_LX90_WY.book Page 109 Wednesday, February 6, 2008 11:49 AM