J1 j3 j2, Installation step 2, Installation step 1 – Edwards Signaling 2400 Series User Manual
Page 73: Led legend
CONNECT J1 AND J2 TO RJ31X OR RJ38X (CA31A OR CA38A IN CANADA) TELEPHONE
JACKS INSTALLED BY AUTHORIZED TELEPHONE COMPANY REPRESENTATIVE. JACKS
MUST BE INSTALLED WITHIN 5 FT. (1.5 M) OF PANEL. PROTECTIVE GROMMET SUPPLIED
FOR ENCLOSURE KNOCKOUT.
=
=
=
=
=
LED OFF
ON STEADY
LED COLOR
RED
SLOW FLASH
2-PHASE FLASH
RAPID FLASH
LED LEGEND
[DIALPRG1.CDR]
10/29/97
=
FIRE ALARM SENT & ACKNOWLEDGED
RED
AMBER
=
SUPERVISORY RESTORE SENT & ACKNOWLEDGED
AMBER
GREEN
=
=
SUPERVISORY ALARM SENT & ACKNOWLEDGED
DIALING
AMBER
=
MODULE DISABLED
AMBER
=
MODULE / PHONE TROUBLE
DIALER LED OPERATION
INSTALLATION STEP 2
A
A
B
C
THE PHONE KEY PAD
IS ONLY FOR MODULE
PROGRAMMING.
(ROTARY DIAL PHONES
WILL NOT WORK).
DIALER WILL AUTOMATICALLY
RECONNECT AFTER 24 HOURS.
LED
DISCONNECT
SWITCH
TROUBLE
1
4
7
2
5
8
0
3
WXY
TUV
PRS
MNO
JKL
GHI
DEF
ABC
6
9
#
*
PROGRAMMING NOTE
DIALER DOES NOT PLACE CALLS OR MONITOR
PANEL OR PHONE LINE WHILE PROGRAMMING
.
!
CAUTION
S1
J1
J3
J2
RING
(RED)
TIP
(GREEN)
RJ31X
8 PIN MODULAR
CONNECTOR FOR
PHONE LINE #1
RJ31X
8 PIN MODULAR
CONNECTOR FOR
PHONE LINE #2
TO PHONE LINE #2
(WIRED SAME AS
PHONE LINE #1)
PREMISES
PHONES
7 Ft.
(2.13 M)
Use J1 when
using only one
phone circuit
PROGRAMMING
PHONE
BLACK
YELLOW
SURGE
PROTECTOR
1
8
7
6
5
4
3
2
1
8
7
6
5
4
3
2
PROGRAMMING STEP A - ENTER PROGRAMMING MODE
CONNECT PHONE TO J3
TAKE HANDSET OFF-HOOK.
GREEN
J1
J3
J2
PROGRAMMING STEP D - EXIT PROGRAMMING MODE
DISCONNECT PHONE FROM J3
J1
J3
J2
PUT HANDSET ON-HOOK.
OR
AMBER ON RED
*
PROGRAMMING ITEM 04 - SECONDARY CMS PHONE NUMBER
UP TO 24 DIGIT PHONE NUMBER
0
4
(DEFAULT= 2)
*
PROGRAMMING ITEM 05 - 1 OR 2 PHONE LINE OPERATION
OR
1
2
AMBER ON GREEN
0
5
*
PROGRAMMING ITEM 06 - NUMBER OF CMS RETRY CALLS
5, 6, 7, 8, 9, & 0 (10) ARE VALID
ENTRIES (DEFAULT = 10)
GREEN
0
6
0 - 99 SECONDS. ARE VALID
ENTRIES (DEFAULT = 0)
GREEN
*
PROGRAMMING ITEM 07 - RETRY INTERVAL
0
7
AMBER
PROGRAMMING ITEM 08 - AC FAILURE DELAY
0 - 18 HOURS ARE VALID ENTRIES
(DEFAULT = 0)
*
0
8
AMBER
PROGRAMMING ITEM 09 - FIRST SUPERVISION CALL DELAY
2 DIGIT DELAY IN HOURS. (0 - 18)
NOTE: DELAY TIME STARTS AT THE NEXT POWER ON.
(DEFAULT = 12)
*
0
9
PROGRAMMING ITEM 10 - 24 HR. TROUBLE RETRANSMISSION CHECK IN
PROGRAMMING ITEM 11 - ZONE/CODE ORDER
*
OR
ENABLE
DISABLE
(DEFAULT)
1
1
0
2
RED
AMBER ON RED
*
PROGRAMMING ITEM 02 - PRIMARY CMS PHONE NUMBER
UP T0 24 DIGIT PHONE NUMBER
0
2
*
PROGRAMMING STEP C - ENTER DIALER DATA
2 DIGIT PROGRAMMING ITEM CODE
CONFIRMATION BEEP = VALID ITEM #
ENTER REQUIRED INFORMATION FOR
ALL 11 PROGRAMMING ITEMS.
PROGRAMMING ITEM VERIFICATION
SOUNDS CONTENTS OF
SELECTED ITEM THRU
HANDSET
*
PROGRAMMING
ITEM MUMBER
#
1
0 =
2
3
4
DEFAULT PROGRAM ITEM RESTORATION
ENTERS DEFAULT VALUES &
RETURNS TO PROGRAM STEP C.
0
0
GREEN
*
RED
(Default)
Zone/Code
Code/Zone
OR
*
1
1
2
1
NOTE: IF PHONE NUMBERS HAVE BEEN PREVIOUSLY ENTERED INTO DIALER, DIALER WILL
NOTIFY MONITORING STATION BEFORE PROGRAMMING CAN PROCEED.
GREEN
PROGRAMMING STEP B - ENTER PASSWORD
4 DIGIT PASSWORD
CONFIRMATION BEEP
= VALID PASSWORD
DIALING
GREEN
GENERAL NOTES
1.
CONFIRMATION BEEP INDICATES PROGRAM ITEM ENTERED.
2.
PHONE LINES MUST BE LOOP START ON A PUBLIC SWITCHED NETWORK. PBX, GROUND START, AND PARTY LINES
ARE NOT ACCEPTABLE.
3.
PASSWORD = 4727 (GSBS).
4.
AFTER INITIAL PROGRAMMING, DIALER NOTIFIES CENTRAL MONITORING STATION OF TROUBLE, BEFORE
PROGRAMMING CAN PROCEED.
5.
TWO PHONE LINES ARE REQUIRED TO COMPLY WITH NFPA 72.
6.
DIALER WILL AUTOMATICALLY SWITCH TO PULSE DIALING AFTER THREE CONSECUTIVE FAILURES USING TONE
MODE. DIALER WILL SWITCH BACK TO TONE DIALING AFTER FAILING TO CONNECT USING PULSE MODE, OR UPON
POWER UP.
AMBER ON GREEN
0
1
*
PROGRAMMING ITEM 01 - PRIMARY SITE ID NUMBER
4 DIGIT ID NUMBER
MUST BE 4 DIGITS
USE LEADING ZEROS AS REQUIRED
AMBER ON GREEN
*
PROGRAMMING ITEM 03 - SECONDARY SITE ID NUMBER
0
3
4 DIGIT ID NUMBER
MUST BE 4 DIGITS
USE LEADING ZEROS AS REQUIRED
A
B
STANDOFF
CONTROL PANEL
FACEPLATE
DACT
MODULE
BUS INTERFACE
BOARD
C
STRIPE ON RIBBON
CONNECTOR FACES
DOWN
TO NEXT MODULE
OR BASE PANEL
REAR VIEW
MAIN CONTROL
PANEL
DIALER
MODULE
BUS INTERFACE BOARD
ON REAR OF DIALER MODULE
DO NOT INSTALL
DIALER HERE ON
MULTI-ZONE PANELS
DL1
D
INSTALLATION STEP 1
A
B
C
INSTALL BUS INTERFACE BOARD ON BACK OF DIALER MODULE.
INSTALL DIALER MODULE IN PANEL. SEE PANEL INSTALLATION DRAWING.
CONNECT RIBBON CABLE FROM MAIN CONTROL PANEL OR ADJECENT MODULE
SET PROGRAM SWITCH TO PROGRAM MODE (UP), AND PUSH RESET SWITCH.
WAIT FOR POWER LED TO FLASH, THEN RETURN SWITCH TO NORMAL MODE (DOWN).
Note: This process installs the dialer module in the panel’s database. The panel will remain in trouble until the dialer is
properly wired and programmed.
D