Edwards Signaling 105XBRi Series - Manual

Installation Instructions for Rebel Chameleon TM
105XBRi Series LED Multi-Status Indicator in
NEMA 4X Enclosures
Description
The 105XBRi Series Chameleon Multi-Status LED Indicator
is a UL and cUL listed, multi-color LED signaling appliance
which, when assembled in accordance with these installa-
tion instructions, constitute a UL Listed Type 4X enclosure
and are UL Listed for Marine Use. They are designed for
use in industrial applications or in applications where a Type
4X enclosure is required. When assembled in accordance
with these instructions, the 105XBRi series visual signals
are UL Listed for use in Division 2 Hazardous Locations as
described in Table 1.
The lights are available in 24V DC and 120V 50/60 Hz. They
are available in either Red/Blue/Amber or Red/Green/Amber.
Edwards Signaling's NEW 105XBRi Multi-status Indicator
is more "chameleon-like" than ever. With our new adaptive
design - one device does it all. With a quick change to the
new 105 Chameleon's dip switch settings, these flexible
multi-status indicators instantly adapt for use with or without
control from an external PLC, PAC, or control relay. Now,
regardless of the application you will have just the right device
for the job with only half the inventory.
XTRA-SAFE Enabled
The Chameleon 105XBRi devices ship as standard with
Edwards Signaling's XTRA-SAFE
TM
Technology (patent
pending) Enabled. XTRA-SAFE multi-status indicating
devices employ patented combinations of color AND flash-
rate to provide more definite status indication to those who
are color-blind. With XTRA-SAFE, when Chameleon multi-
status indicators are turned red, they pulse at a rate of 240
flashes per minute, further emphasizing the urgency which
the color red typically connotes. When amber, these devices
pulse at a "less urgent" rate of 120 flashes per minute. When
Chameleon multi-status indicators are turned blue or green
and no other colors are energized, the Chameleon devices
remain "steady-on" and do not flash. Even in extreme cases
where no color is perceived, flash-rate variation provides a
redundant layer of visual indication.
P/N 3101612 ISSUE 3
© 2010
http://www.edwardssignaling.com Phone: (800) 336-4206 Fax: (800) 454-2363
When XTRA-SAFE Technology is enabled, and multiple col-
ors are energized, the device will cycle through the energized
colors at the following pre-set flash-rates:
Red: 240 FPM
Amber: 120 FPM
Green or Blue: 65 FPM
XTRA-SAFE Disabled
While in most cases, the added layer of safety gained by op-
erating a multi-status indicator with XTRA-SAFE Technology
is desirable, some applications may not require differentiation
in flash rates. In other applications, changes do not corre-
spond to escalating levels of urgency. The adaptive design
of the new Chameleon 105 XBRi allows the product to be
adapted to accommodate these requirements by configuring
the dipswitches as shown in Figure 1 (Applications WITH-
OUT a separate PLC or Controller - XTRA-SAFE Technology
Disabled). With XTRA-SAFE Disabled, when red or amber,
the unit pulses at a rate of 65 flashes per minute. When
Chameleon multi-status indicators are turned green or blue
and no other colors are energized, the Chameleon devices
remain "steady on" and do not flash.
When XTRA-SAFE Technology is disabled, and multiple col-
ors are energized, the device will cycle through the energized
colors at 65 FPM.
Externally Controlled
The Chameleon multi-status indicators can also be used in
applications where they will be controlled "externally" us-
ing a Programmable Logic Controller (PLC) or other such
external controller. When externally controlled by a PLC,
activation of colors and flash-rate are fully customizable,
and can be programmatically determined. In applications,
where multiple colors are activated simultaneously, the lights
operate on a priority with red highest, amber second and blue
or green, the lowest. Refer to Figure 1 (Applications WITH
a separate PLC or Controller).Wire color corresponds with
each indicated color.
Red wire = Red LED's
Yellow wire = Amber LED's
Blue with Green tracer wire = Green or Blue LED's
Table 1. Hazardous Location Ratings
Cat. No. Class Division Group Operating Temperature
105XBRiRGA24D
105XBRiRGA120A
I 2 A, B, C, D T5 (100C, 212F)
II 2 F, G T5 (100C, 212F)
III T5 (100C, 212F)
105XBRiRBA24D
105XBRiRBA120A
I 2 A, B, C, D T6 (85C, 185F)
II 2 F, G T6 (85C, 185F)
III T6 (85C, 185F)