Edwards Signaling ZG4RB - Manual

Installation Sheet 28JAN05 P/N: 3100272 REV: 3.0
Genesis Speaker 1 / 2
Genesis Speaker
Product information
The Genesis Speaker is an audible fire alarm notification
appliance designed for indoor walls. See Table 1 for a list of
model numbers.
The speaker includes a field configurable switch for selecting
the desired wattage tap. The wattage tap setting remains
visible after final installation.
Install this device in accordance with applicable requirements
in the latest editions of the NFPA codes and standards;
Canadian Electrical Code, Part 1, Section 32; and in
accordance with the local authorities having jurisdiction.
These instructions apply to the following model numbers:
Table 1: Models
Description Model number
Speaker,
25 Vrms, white ADTG4-S2 MG4-S2
EG4-S2 XLSG4-S2
G4-S2 ZG4-S2
G4-S2-LG
Speaker,
25 Vrms, white, with
FIRE marking ADTG4F-S2 MG4F-S2
EG4F-S2 XLSG4F-S2
G4F-S2 ZG4F-S2
G4F-S2-LG
Speaker,
70 Vrms, white ADTG4-S7 MG4-S7
EG4-S7 XLSG4-S7
G4-S7 ZG4-S7
G4-S7-LG
Speaker,
70 Vrms, white, with
FIRE marking
ADTG4F-S7 MG4F-S7
EG4F-S7 XLSG4F-S7
G4F-S7 ZG4F-S7
G4F-S7-LG
Surface mount box,
white ADTG4B MG4B
EG4B XLSG4B
G4B ZG4B
G4B-LG
Table 1: Models
Description Model number
Surface mount box,
red ADTG4RB MG4RB
EG4RB XLSG4RB
G4RB ZG4RB
G4RB-LG
Specifications
Operating voltage: 25 Vrms (model S2), 70 Vrms (model S7)
Supervisory voltage: 30 V maximum
Sound level output: See Table 2
Speaker response: 400 to 4,000 Hz
Wire size: 12 to 18 AWG (2.50 to 0.75 sq mm)
Compatible electrical boxes
North American 4 in square electrical box, 2-1/8 in deep
(UL/ULC listed flush mounted with no extension ring)
Surface mount box: See Table 1
Operating environment
Temperature: 32 to 120 °F (0 to 49 °C)
Humidity: 0 to 93% RH, noncondensing at 90 °F (32 °C)
Intended installation environment: Indoor dry
Agency listings: Meets ULC-S541 and UL 1480 fifth edition
Table 2: Sound level output (dBA)
Wattage Output
1/4 W 80
1/2 W 83
1 W 86
2 W 89
dBA = Decibels, A-weighted
UL 1480: Sound level output at 10 ft (3.05 m) measured in a
reverberant room using 400 to 4,000 Hz band limited pink
noise.
ULC-S541: Meets or exceeds 85 dBA in an anechoic chamber
at 10 ft (3.05 m).
Directional characteristics: Within 6 dB of on-axis sound level
when measured 90
° off-axis (horizontal).
Installation instructions
Caution: Electrical supervision requires the wire run to be
broken at each terminal. Do not loop the signaling circuit field
wires around the terminals.
To install the speaker:
1. Remove the cover by depressing the tabs on top of the
unit by inserting a small screwdriver from the top and
twisting slightly.
2. Connect wires as shown. Strobe terminals S+ and S- are
not used for speaker only devices. See the Figure 1.