Edwards Signaling Genesis Strobe - Manual

Installation Sheet 07OCT05 P/N: 3100559 REV: 3.0
Genesis Strobe 1 / 2
Genesis Strobe
Product information
The Genesis Strobe is a visible fire alarm notification appliance
designed for indoor walls. See Table 1 for a list of model
numbers.
The strobe includes a field configurable switch for selecting the
desired candela output and a field configurable jumper for the
strobe signal output. The candela output setting is locked in
place and remains visible after final installation.
This strobe features an enhanced synchronization circuit to
comply with the latest requirements of UL 1971 Signaling
Devices for the Hearing Impaired and the latest Canadian
standard CAN/ULC S526-02. Synchronized operation requires
a separately installed synchronization control module. See
Table 2 for a list of compatible synchronization modules.
Install this device in accordance with applicable requirements
in the latest editions of the NFPA codes and standards and
Canadian Electrical Code, Part 1, Section 32, CAN/ULC S524-
01, Standard for the Installation of Fire Alarm Systems, and in
accordance with the local authorities having jurisdiction.
Table 1: Models
Description Model number
Strobe,
15 to 110 multi-cd,
white ADTG1-VM MG1-VM
EG1-VM XLSG1-VM
G1-VM ZG1-VM
G1-VM-LG
Strobe,
15 to 110 multi-cd,
white, with FIRE marking ADTG1F-VM MG1F-VM
EG1F-VM XLSG1F-VM
G1F-VM
ZG1F-VM
G1F-VM-LG
Strobe,
15 to 110 multi-cd,
red ADTG1R-VM MG1R-VM
EG1R-VM XLSG1R-VM
G1R-VM
ZG1R-VM
G1R-VM-LG
Table 1: Models
Description Model number
Strobe,
15 to 110 multi-cd,
red, with FIRE marking ADTG1RF-VM MG1RF-VM
EG1RF-VM XLSG1RF-VM
G1RF-VM ZG1RF-VM
G1RF-VM-LG
Trim plate,
white ADTG1T MG1T
EG1T XLSG1T
G1T ZG1T
G1T-LG
Trim plate,
white, with FIRE marking ADTG1T MG1T
EG1T XLSG1T
G1T ZG1T
G1T-LG
Trim plate,
red ADTG1RT MG1RT
EG1RT
XLSG1RT
G1RT ZG1RT
G1RT-LG
Trim plate,
red, with FIRE marking ADTG1RT MG1RT
EG1RT
XLSG1RT
G1RT ZG1RT
G1RT-LG
Table 2: Compatible synchronization modules
Description Model number
Auto-Sync Output
Module SIGA-CC1S SIGA-MCC1S
SIGA-CC1S-LG SIGA-MCC1S-LG
Genesis Signal Master
Snap-on Mount ADTG1M MG1M
EG1M
XLSG1M
G1M ZG1M
G1M-LG
Genesis Signal Master -
Remote Mount ADTG1M-RM MG1M-RM
EG1M-RM XLSG1M-RM
G1M-RM ZG1M-RM
G1M-RM-LG
Specifications
Operating voltage: 24 Vdc or 24 Vfwr, nominal
Strobe operating current: See Table 3
Light output: Selectable at 15, 30, 75, and 110 cd
Synchronization: Meets UL 1971 requirements. Maximum
allowed resistance between any two devices is 20 Ω.
Refer to specifications for the synchronization control
module, this strobe, and the control panel to determine
allowed wire resistance.
Wire size: 12 to 18 AWG (2.50 to 0.75 sq mm)
Compatible electrical boxes
North American 2-1/2 in (64 mm) deep 1-gang box
Standard 4 in square box 1-1/2 in (38 mm), 2-gang, or 4 in
octagonal with G1T or G1RT trim accessory
Operating environment
Temperature: 32 to 120 °F (0 to 49 °C)
Humidity: 0 to 93% RH, noncondensing at 90 °F (32 °C)