Watlow Series 97 - Manual (Page 85)

Wa t l o w S e r i e s 9 7 A p p e n d i x ■ A . 2 3
Prompt Index
[4``1] Output Calibration 4, 1V 6.21
[4``4] Output Calibration 4, 4mA 6.21
[4`10] Output Calibration 4, 10V 6.21
[4`20] Output Calibration 4, 20mA 6.21
A
[A2hi] Alarm 2 High 6.5
[A2lo] Alarm 2 Low 6.5
[A3hi] Alarm 3 High 6.6
[A3lo] Alarm 3 Low 6.5
[A4hi] Alarm 4 High 6.6
[A4lo] Alarm 4 Low 6.6
[ACAL] Analog Output Offset 6.13
[Acnt] Ambient A-D Counts 6.19
[Addr] Address 6.14
[A`hi] Analog Output High 6.14
[Al`2] Alarm 2 Status 6.4
[Al`3] Alarm 3 Status 6.4
[Al`4] Alarm 4 Status 6.4
[Alm] Alarm Menu 6.5-6.6
[A`Lo] Analog Output Low 6.13
[Amb] Ambient Temperature 6.19
[Anu2] Alarm Annunciation 2 6.11
[Anu3] Alarm Annunciation 3 6.12
[Anu4] Alarm Annunciation 4 6.13
[Aout] Analog Output 4 6.13
B
[baUd] Baud Rate 6.13
C
[`Cal] Calibration Menu Lock 6.17
[Cal1] Calibration Offset 6.5
[cin1] Input Calibration Menu A.11
[`C-f] C or F 6.16
[cnt1] Channel 1 A-D Counts 6.19
[cnt2] Channel 2 A-D Counts 6.19
[cout] Output Calibration Menu A.11
D
[date] Date of Manufacture 6.17
[deC1] Decimal 1 6.8
[dfLt] Default Settings 6.20
[diag] Diagnostics Menu 6.17-6.19
[disp] Display Menu 6.14-6.16
[dIsp] Test Display 6.19
E
[E`cn] Event Condition 6.9
[E`Fn] Event Function 6.9
[`Err] Input Error Latching 6.16
[E`St] Event Input Status 6.4
F
[Fcty] Factory Page menus 6.17-6.21
[ftr1] Input Software Filter 1 6.8
G
[glbl] Global Menu 6.16
[`gnd] Set Ground 6.20
H
[hres] High Resolution 6.19
[hys2] Alarm Hysteresis 2 6.10
[hys3] Alarm Hysteresis 3 6.11
[hys4] Alarm Hysteresis 4 6.12
I J K
[In`1] Input 1 6.7
[In`2] Input 2 6.9
[Inp1] Input 1 Menu 6.7-6.8
[Inp2] Input 2 Menu 6.9
[Ity2] Input 2 Hardware Enabled 6.18
L
[Lat2] Latching 2 6.10
[Lat3] Latching 3 6.11
[Lat4] Latching 4 6.12
[LdSp] Lower Display 6.16
[lead] Lead Resistance Calibration 6.20
[L9c2] Alarm Logic 2 6.10
[L9c3] Alarm Logic 3 6.11
[L9c4] Alarm Logic 4 6.13
[L`hi] High Limit Set Point 6.5
[Lhys] Limit Hysteresis 6.9
LiM] Limit Menu 6.5
[[Line] Line Frequency 6.19
[L`Lo] Low Limit Set Point 6.5
[`LOC] Lockout Menu 6.17
[Lo`l] Lower Display User Limit Message 6.16
[Lo`s] Lower Display User Safe Message 6.16
[LSid] Limit Active Sides 6.9
[L`St] Limit Status 6.4
M N
[Mdl] Model Number 6.17
[Mon] Monitor Menu 6.4
O
[Oper] Operations Page menus 6.4-6.6
[Oper] Operations Page Mode Lock 6.17
[Oty1] Output 1 Hardware 6.18
[Oty2] Output 2 Hardware 6.18
[Oty3] Output 3 Hardware 6.18
[Oty4] Output 4 Hardware 6.18
[Ot`2] Output 2 6.9
[Ot`3] Output 3 6.11
[Ot`4] Output 4 6.12
[Out1] Output 1 Menu 6.9
[Out2] Output 2 Menu 6.9-6.11
[Out3] Output 3 Menu 6.11-6.12
[Out4] Output 4 Menu 6.12-6.14
P Q
[Pr`1] Process 1 6.4
[Prc4] Process 4 Type 6.13
R
[r`15] RTD Calibration, 15 Ω 6.20
[r380] RTD Calibration, 380 Ω 6.20
[`reu] Software Revision 6.18
[rh`1] Range High 1 6.8
[rl`1] Range Low 1 6.8
[`rst] Restore Factory Calibration 6.20
S
[sen1] Sensor Type 1 6.7
[`Set] Setup Page menus 6.7-6.16
[`Set] Setup Page Lock 6.17
[Sid2] Alarm Active Sides 2 6.10
[Sid3] Alarm Active Sides 3 6.11
[Sid4] Alarm Active Sides 4 6.12
[SiL2] Silencing 2 6.10
[SiL3] Silencing 3 6.11
[Sil4] Silencing 4 6.12
[`Sn1] Serial Number 1 6.18
[`Sn2] Serial Number 2 6.18
[Soft] Software ID Number 6.18
T
[tc00] Thermocouple Calibration, 0mV 6.20
[tc32] Thermocouple Calibration, 32° 6.20
[tc50] Thermocouple Calibration, 50mV 6.20
[tout] Test Output 6.19
[tsht] Communications Test/ Troubleshooting
6.19
U V W X Y Z
[Udsp] Upper Display 6.14
[Up`l] Upper Display User Limit Message 6.15