Ransburg No. 2 Air Motor Atex Approved Unit 80086-XX User Manual

Page 9

AH----12

12----01.03 No. 2 Air Motor Handgun

01.03 No. 2 Air Motor Handgun

EUROPEAN ATEX DIRECTIVE 94/9/EC, ANNEX II, 1.0.6

The following instructions apply to equipment covered

The following instructions apply to equipment covered
by certificate number Sira 12ATEX5006X:

by certificate number Sira 12ATEX5006X:

by certificate number Sira 12ATEX5006X:

The equipment may be used with flammable gases

The equipment may be used with flammable gases

The equipment may be used with flammable gases
and vapors with apparatus groups II and with temper-

and vapors with apparatus groups II and with temper-

and vapors with apparatus groups II and with temper-
ature class T6.

ature class T6.

ature class T6.

The equipment is only certified for use in ambient

The equipment is only certified for use in ambient

The equipment is only certified for use in ambient
temperatures in the range 0

temperatures in the range 0

temperatures in the range 0 °C to +40

C to +40

C to +40°C and should

C and should

not be used outside this range.

not be used outside this range.

Installation shall be carried out by suitably trained

Installation shall be carried out by suitably trained

Installation shall be carried out by suitably trained
personnel in accordance with the applicable code of

personnel in accordance with the applicable code of

personnel in accordance with the applicable code of
practice e.g. EN 60079

practice e.g. EN 60079

practice e.g. EN 60079----14:1997.

14:1997.

Special conditions of the certificate require the power

Special conditions of the certificate require the power
supply to be located a minimum of 6.1 m (20’) out-

supply to be located a minimum of 6.1 m (20’) out-

supply to be located a minimum of 6.1 m (20’) out-
side or away from the target being sprayed. It is the

side or away from the target being sprayed. It is the

side or away from the target being sprayed. It is the
end users’ responsibility to insure this products spe-

end users’ responsibility to insure this products spe-

end users’ responsibility to insure this products spe-
cial condition are met when equipment is installed

cial condition are met when equipment is installed

cial condition are met when equipment is installed
and used.

and used.

and used.

Inspection and maintenance of this equipment shall

Inspection and maintenance of this equipment shall

Inspection and maintenance of this equipment shall
be carried out by suitably trained personnel in accord-

be carried out by suitably trained personnel in accord-

be carried out by suitably trained personnel in accord-
ance with the applicable code of practice e.g. EN

ance with the applicable code of practice e.g. EN

ance with the applicable code of practice e.g. EN
60079

60079

60079----17.

17.

Repair of this equipment shall be carried out by suita-

Repair of this equipment shall be carried out by suita-
ble trained personnel in accordance with the applica-

ble trained personnel in accordance with the applica-

ble trained personnel in accordance with the applica-
ble code of practice e.g. EN 60079

ble code of practice e.g. EN 60079

ble code of practice e.g. EN 60079----19.

19.

Putting into service, use, assembling, and adjustment

Putting into service, use, assembling, and adjustment
of the equipment shall be fitted by suitably trained

of the equipment shall be fitted by suitably trained

of the equipment shall be fitted by suitably trained
personnel in accordance with the manufacturer's doc-

personnel in accordance with the manufacturer's doc-

personnel in accordance with the manufacturer's doc-
umentation.

umentation.

umentation.

Refer to the "Table of Contents" of this service manu-

Refer to the "Table of Contents" of this service manu-

Refer to the "Table of Contents" of this service manu-
al:

al:

Installation

Operation

Maintenance

Maintenance
Parts Identification

Parts Identification

Components to be incorporated into or used as re-

placement parts of the equipment shall be fitted by

placement parts of the equipment shall be fitted by
suitably trained personnel in accordance with the

suitably trained personnel in accordance with the

suitably trained personnel in accordance with the
manufacturer's documentation.

manufacturer's documentation.

The certification of this equipment relies upon the fol-

The certification of this equipment relies upon the fol-
lowing materials used in its construction:

lowing materials used in its construction:

lowing materials used in its construction:

If the equipment is likely to come into contact with

If the equipment is likely to come into contact with

If the equipment is likely to come into contact with
aggressive substances, then it is the responsibility of

aggressive substances, then it is the responsibility of

aggressive substances, then it is the responsibility of
the user to take suitable precautions that prevent it

the user to take suitable precautions that prevent it

the user to take suitable precautions that prevent it
from being adversely affected, thus ensuring that the

from being adversely affected, thus ensuring that the

from being adversely affected, thus ensuring that the
type of protection provided by the equipment is not

type of protection provided by the equipment is not

type of protection provided by the equipment is not
compromised.

compromised.

compromised.

Aggressive substances: e.g. acidic liquids or gases

Aggressive substances: e.g. acidic liquids or gases

Aggressive substances: e.g. acidic liquids or gases
that may attack metals, or solvents that may affect

that may attack metals, or solvents that may affect

that may attack metals, or solvents that may affect
polymeric materials.

polymeric materials.

polymeric materials.

Suitable precautions: e.g. regular checks as part of

Suitable precautions: e.g. regular checks as part of

Suitable precautions: e.g. regular checks as part of
routine inspections or establishing from the material's

routine inspections or establishing from the material's

routine inspections or establishing from the material's
data sheets that it is resistant to specific chemicals.

data sheets that it is resistant to specific chemicals.

data sheets that it is resistant to specific chemicals.

Refer to "Specifications" in the "Introduction" section:

Refer to "Specifications" in the "Introduction" section:

•

All fluid passages contain stainless steel

All fluid passages contain stainless steel
or nylon fittings.

or nylon fittings.

•

High voltage cascade is encapsulated with

High voltage cascade is encapsulated with
a di

a di

a di----electric oil.

electric oil.

A recapitulation of the certification marking is detailed

A recapitulation of the certification marking is detailed
in the "Atex" section, on the next page, drawing num-

in the "Atex" section, on the next page, drawing num-

in the "Atex" section, on the next page, drawing num-
bers: 80108, 80082, 80083 and 80088.

bers: 80108, 80082, 80083 and 80088.

bers: 80108, 80082, 80083 and 80088.

The characteristics of the equipment shall be detailed

The characteristics of the equipment shall be detailed

The characteristics of the equipment shall be detailed
e.g. electrical, pressure, and voltage parameters.

e.g. electrical, pressure, and voltage parameters.

e.g. electrical, pressure, and voltage parameters.

The manufacturer should note that, on being put into

The manufacturer should note that, on being put into

The manufacturer should note that, on being put into
service, the equipment must be accompanied by a

service, the equipment must be accompanied by a

service, the equipment must be accompanied by a
translation of the instructions in the language or lan-

translation of the instructions in the language or lan-

translation of the instructions in the language or lan-
guages of the country in which the equipment is to be

guages of the country in which the equipment is to be

guages of the country in which the equipment is to be
used and by the instructions in the original language.

used and by the instructions in the original language.

INTRODUCTION