Use of lsch0009 dielec – Ransburg No. 2 Air Motor Atex Approved Unit 80086-XX User Manual

Page 44

AH----12

12----01.03 No. 2 Air Motor Handgun

01.03 No. 2 Air Motor Handgun

1. Insure the power is turned off on the front

1. Insure the power is turned off on the front
panel switch. If possible disconnect the line

panel switch. If possible disconnect the line

panel switch. If possible disconnect the line
cord to the unit.

cord to the unit.

2. Insert a flat bladed screwdriver into the slot

2. Insert a flat bladed screwdriver into the slot
of the fuse holder. Push the end of the fuse

of the fuse holder. Push the end of the fuse

of the fuse holder. Push the end of the fuse
holder in and turn counter

holder in and turn counter

holder in and turn counter----clock wise to remove

clock wise to remove

the fuse.

3. Inspect the fuse, insure it is the proper fuse

3. Inspect the fuse, insure it is the proper fuse
to give the proper protection. If faulty, replace

to give the proper protection. If faulty, replace

to give the proper protection. If faulty, replace
as required.

as required.

4. Insert the end of the fuse holder back with

4. Insert the end of the fuse holder back with
the fuse in the center and push down while

the fuse in the center and push down while

the fuse in the center and push down while
turning the holder 1/4 turn clock

turning the holder 1/4 turn clock

turning the holder 1/4 turn clock----wise to lock

wise to lock

back in place.

Use of LSCH0009 Dielec-

Use of LSCH0009 Dielec-
tric Grease in No. 2 Hand-

tric Grease in No. 2 Hand-

tric Grease in No. 2 Hand-
gun

gun

Misuse of the LSCH0009 dielectric grease in-

Misuse of the LSCH0009 dielectric grease in-
side the No. 2 Handgun can cause premature

side the No. 2 Handgun can cause premature

side the No. 2 Handgun can cause premature
failure of the electric motor. Dielectric grease

failure of the electric motor. Dielectric grease

failure of the electric motor. Dielectric grease
should only be used as a filler (displacement of

should only be used as a filler (displacement of

should only be used as a filler (displacement of
air) to suppress high voltage corona. Dielectric

air) to suppress high voltage corona. Dielectric

air) to suppress high voltage corona. Dielectric
grease should only be applied to the following

grease should only be applied to the following

grease should only be applied to the following
parts:

parts:

parts:

Exposed high voltage cable of the gun end of

Exposed high voltage cable of the gun end of

the 19370

the 19370----xx high voltage cable end

xx high voltage cable end

Inside the white 6204

Inside the white 6204----00 high voltage resistor

00 high voltage resistor

housing

On the inside and outside of the 2842

On the inside and outside of the 2842----01 (525

01 (525

megohms) high voltage resistor

The use of LSCH0009 dielectric grease or any

The use of LSCH0009 dielectric grease or any
other lubricants on any components associative

other lubricants on any components associative

other lubricants on any components associative
with the electric motor, drive shaft assembly,

with the electric motor, drive shaft assembly,

with the electric motor, drive shaft assembly,
and ground circuit is forbidden. Due to these

and ground circuit is forbidden. Due to these

and ground circuit is forbidden. Due to these
areas direct contact to the D.C. motor, lubri-

areas direct contact to the D.C. motor, lubri-

areas direct contact to the D.C. motor, lubri-
cants can migrate into the motor and cause it to

cants can migrate into the motor and cause it to

cants can migrate into the motor and cause it to
fail. Dielectric grease SHOULD NOT be applied

fail. Dielectric grease SHOULD NOT be applied

fail. Dielectric grease SHOULD NOT be applied
to the following areas of the No. 2 Handgun:

to the following areas of the No. 2 Handgun:

7225 drive shaft assembly

4175

4175----01 shaft (ground) resistor (10

01 shaft (ground) resistor (10

G Ohms)

Components of the shaft seal/ bearing

assembly at the front end of the drive

assembly at the front end of the drive
shaft

shaft

Special care is and has always been taken dur-

Special care is and has always been taken dur-
ing manufacturing of the gun to apply the dielec-

ing manufacturing of the gun to apply the dielec-

ing manufacturing of the gun to apply the dielec-
tric grease only to those areas noted. Gun fail-

tric grease only to those areas noted. Gun fail-

tric grease only to those areas noted. Gun fail-
ure associated with misuse of dielectric grease

ure associated with misuse of dielectric grease

ure associated with misuse of dielectric grease
will not be covered under warranty.

will not be covered under warranty.

MAINTENANCE