Shutdown – Ransburg No. 2 Air Motor Atex Approved Unit 80086-XX User Manual

Page 24

AH----12

12----01.03 No. 2 Air Motor Handgun

01.03 No. 2 Air Motor Handgun

BEFORE attempting any cleaning or

color change procedures, the high voltage

color change procedures, the high voltage
and the AC power to the power supply

and the AC power to the power supply

and the AC power to the power supply
MUST be turned OFF!

MUST be turned OFF!

W A R N I N G

1. Release the trigger. Allow two to five sec-

1. Release the trigger. Allow two to five sec-
onds for the paint to quit flowing off the bell

onds for the paint to quit flowing off the bell

onds for the paint to quit flowing off the bell
then turn OFF the gun motor. Turn the pow-

then turn OFF the gun motor. Turn the pow-

then turn OFF the gun motor. Turn the pow-
er supply OFF (at the booth wall switch for

er supply OFF (at the booth wall switch for

er supply OFF (at the booth wall switch for
permanent installations or at the master

permanent installations or at the master

permanent installations or at the master
switch on the power supply for mobile oper-

switch on the power supply for mobile oper-

switch on the power supply for mobile oper-
a

attttiiiio

s))))....

2. Place the feed tube in the one o’clock po-

2. Place the feed tube in the one o’clock po-
sition. Loosen the set screw on the bell hub.

sition. Loosen the set screw on the bell hub.

sition. Loosen the set screw on the bell hub.
Then hold the shaft collar with one hand and

Then hold the shaft collar with one hand and

Then hold the shaft collar with one hand and
turn the bell on the shaft with the other hand

turn the bell on the shaft with the other hand

turn the bell on the shaft with the other hand
as you pull it forward off the shaft.

as you pull it forward off the shaft.

3. Clean the bell with a soft brush

3. Clean the bell with a soft brush
(nonmetallic) or cloth and a suitable solvent.

(nonmetallic) or cloth and a suitable solvent.

(nonmetallic) or cloth and a suitable solvent.
The bell MUST be cleaned if the spraying is

The bell MUST be cleaned if the spraying is

The bell MUST be cleaned if the spraying is
to be interrupted for more than a few

to be interrupted for more than a few

to be interrupted for more than a few
minutes.

minutes.

Shutdown

These steps are to be followed during a

These steps are to be followed during a
shutdown for short periods such as breaks,

shutdown for short periods such as breaks,

C A U T I O N

The bell MUST be cleaned if the gun

will not be operated again within a

will not be operated again within a
few minutes. If two component cata-

few minutes. If two component cata-

few minutes. If two component cata-
lyzed paint is used, frequent bell

lyzed paint is used, frequent bell

lyzed paint is used, frequent bell
cleaning and flushing may be re-

cleaning and flushing may be re-

cleaning and flushing may be re-
quired. (See "Color Change" in the

quired. (See "Color Change" in the

quired. (See "Color Change" in the
"Operation" section.)

"Operation" section.)

C A U T I O N

DO NOT

soak the bell in solvent as

this

may deteriorate its black conductive

may deteriorate its black conductive
coating. See Service Instruction

coating. See Service Instruction

coating. See Service Instruction
"Solvent Effects on #2 Handgun Bell /

"Solvent Effects on #2 Handgun Bell /

"Solvent Effects on #2 Handgun Bell /
Brush Wear" and "Paint and Solvent

Brush Wear" and "Paint and Solvent

Brush Wear" and "Paint and Solvent
Specifications" in the "Appendix" sec-

Specifications" in the "Appendix" sec-

Specifications" in the "Appendix" sec-
tion of this manual.

tion of this manual.

4. Dry the bell and reinstall it on the shaft. Re

4. Dry the bell and reinstall it on the shaft. Re
----position the feed tube and contact brush.

position the feed tube and contact brush.

End of Shift

These steps are to be followed during a shut-

These steps are to be followed during a shut-
down for extended periods of time exceeding

down for extended periods of time exceeding

down for extended periods of time exceeding
one hour. Time may vary according to the

one hour. Time may vary according to the

one hour. Time may vary according to the
applications and material being used.

applications and material being used.

1. Release the trigger and allow the bell to

1. Release the trigger and allow the bell to
rotate until it is clear of paint. Then turn the

rotate until it is clear of paint. Then turn the

rotate until it is clear of paint. Then turn the
gun motor OFF.

gun motor OFF.

2. Turn the power supply OFF. The power sup-

ply must be “OFF” to perform any cleaning or

ply must be “OFF” to perform any cleaning or
maintenance.

maintenance.

3. Remove and clean the bell (follow the

3. Remove and clean the bell (follow the
steps under "Shutdown" in the "Operation"

steps under "Shutdown" in the "Operation"

steps under "Shutdown" in the "Operation"
section).

section).

section).

4. Place the gun (bell angled down) on the

4. Place the gun (bell angled down) on the

4. Place the gun (bell angled down) on the
gun support rack to prevent solvent and paint

gun support rack to prevent solvent and paint

gun support rack to prevent solvent and paint
from getting into the unit.

from getting into the unit.

from getting into the unit.

5. Flush the paint hose, gun, and feed tube

5. Flush the paint hose, gun, and feed tube

5. Flush the paint hose, gun, and feed tube
with solvent.

with solvent.

OPERATION