Power supply, Fluid hose – Ransburg No. 2 Air Motor Atex Approved Unit 80086-XX User Manual

Page 14

AH----12

12----01.03 No. 2 Air Motor Handgun

01.03 No. 2 Air Motor Handgun

Before attempting to install the equipment, en-

Before attempting to install the equipment, en-
sure that all the necessary components are

sure that all the necessary components are

sure that all the necessary components are
available (see "Parts Identification" section of

available (see "Parts Identification" section of

available (see "Parts Identification" section of
this manual). In addition, read all the technical

this manual). In addition, read all the technical

this manual). In addition, read all the technical
and safety literature that is provided. If the liter-

and safety literature that is provided. If the liter-

and safety literature that is provided. If the liter-
ature is not available, contact your local

ature is not available, contact your local

ature is not available, contact your local
Ransburg Distributor where the equipment was

Ransburg Distributor where the equipment was

Ransburg Distributor where the equipment was
purchased.

purchased.

Power Supply

(Refer to Figure 2)

1. The high voltage power supply MUST be locat-

1. The high voltage power supply MUST be locat-
ed at least 6.1 m (20 feet) from the spraying oper-

ed at least 6.1 m (20 feet) from the spraying oper-

ed at least 6.1 m (20 feet) from the spraying oper-
ation. If a spray booth is used, the power supply

ation. If a spray booth is used, the power supply

ation. If a spray booth is used, the power supply
may be located 1.5 m (5 feet) from the nearest

may be located 1.5 m (5 feet) from the nearest

may be located 1.5 m (5 feet) from the nearest
opening and outside the booth .

opening and outside the booth .

opening and outside the booth .

2. If a line cord is used instead of a permanent

2. If a line cord is used instead of a permanent

2. If a line cord is used instead of a permanent
conduit connection, ensure the ground lead is

conduit connection, ensure the ground lead is

conduit connection, ensure the ground lead is
present on the plug. Ensure that the electrical out-

present on the plug. Ensure that the electrical out-

present on the plug. Ensure that the electrical out-
let is properly wired by using the circuit tester

let is properly wired by using the circuit tester

let is properly wired by using the circuit tester
(20868

(20868

(20868----00). Attach the green ground wire to a

00). Attach the green ground wire to a

proven, true earth ground (i.e., water pipe or elec-

proven, true earth ground (i.e., water pipe or elec-
trical conduit).

trical conduit).

•

The power source wiring and the power

supply connections to it MUST meet all local

supply connections to it MUST meet all local
fire and electrical code standards and comply

fire and electrical code standards and comply

fire and electrical code standards and comply
with all appropriate local and national health

with all appropriate local and national health

with all appropriate local and national health
and safety codes.

and safety codes.

and safety codes.

•

All power supplies MUST be grounded

All power supplies MUST be grounded
to a known true earth ground

to a known true earth ground

to a known true earth ground before any

before any

other connections are made or functions

other connections are made or functions
performed. DO NOT use the power sup-

performed. DO NOT use the power sup-

performed. DO NOT use the power sup-
ply ground wire to ground the target ob-

ply ground wire to ground the target ob-

ply ground wire to ground the target ob-
jects (use LSME4000

jects (use LSME4000

jects (use LSME4000----00 clamp assem-

00 clamp assem-

bly)!

W A R N I N G

3. After the power supply is grounded to a

3. After the power supply is grounded to a
suitable earth ground, the high voltage cable

suitable earth ground, the high voltage cable

suitable earth ground, the high voltage cable
may be connected. Prior to connection of the

may be connected. Prior to connection of the

may be connected. Prior to connection of the
high voltage cable 15 to 30 ml of 3614

high voltage cable 15 to 30 ml of 3614

high voltage cable 15 to 30 ml of 3614----00

(supplied with applicator ) di

(supplied with applicator ) di----electric oil

electric oil

needs to be added to the power supply. Re-

needs to be added to the power supply. Re-
fer to figure 3 for illustration of where the oil

fer to figure 3 for illustration of where the oil

fer to figure 3 for illustration of where the oil
should be inserted.

should be inserted.

should be inserted.

4. Attach the female nut of the high voltage

4. Attach the female nut of the high voltage

4. Attach the female nut of the high voltage
cable to the male threads of the connection

cable to the male threads of the connection

cable to the male threads of the connection
of the power supply.

of the power supply.

Fluid Hose

(Refer to Figure 4)

Install the fluid filter (Item 6) to the applicator,

Install the fluid filter (Item 6) to the applicator,
then to the fluid delivery hose. Attach one

then to the fluid delivery hose. Attach one

then to the fluid delivery hose. Attach one
end of the fluid hose to the adapter (Item 8)

end of the fluid hose to the adapter (Item 8)

end of the fluid hose to the adapter (Item 8)
(Refer to figure 4). This adapter has a 3/8

(Refer to figure 4). This adapter has a 3/8

(Refer to figure 4). This adapter has a 3/8----18

NPSM (F) for attachment to a suitable fluid

NPSM (F) for attachment to a suitable fluid
source.

source.

source. To meet various length requirements,

To meet various length requirements,

the hose fitting on one end has not been at-

the hose fitting on one end has not been at-
tached.

tached.

tached.

Figure 5 illustrates the assembly procedure

Figure 5 illustrates the assembly procedure

Figure 5 illustrates the assembly procedure
for attaching the loose fitting.

for attaching the loose fitting.

W A R N I N G

•

Where the applicator is to be used

Where the applicator is to be used
without a booth, the power supply

without a booth, the power supply

without a booth, the power supply
must located a minimum of 6.1 m

must located a minimum of 6.1 m

must located a minimum of 6.1 m
(20 feet) from the target being

(20 feet) from the target being

(20 feet) from the target being
sprayed.

sprayed.

•

The target Earth Ground and

The target Earth Ground and
Power Supply earth ground must

Power Supply earth ground must

Power Supply earth ground must
be separate earth ground connec-

be separate earth ground connec-

be separate earth ground connec-
tions.

tions.

•

Any hoses either air or fluid that

Any hoses either air or fluid that
are user supplied must be rated

are user supplied must be rated

are user supplied must be rated
for the maximum pressures used

for the maximum pressures used

for the maximum pressures used
for this applicator.

for this applicator.

INSTALLATION