Ransburg No. 2 Air Motor Atex Approved Unit 80086-XX - Manual (Page 6)

AH AH AH AH----12 12 12 12----01.03 No. 2 Air Motor Handgun 01.03 No. 2 Air Motor Handgun 01.03 No. 2 Air Motor Handgun 01.03 No. 2 Air Motor Handgun 6 6 6 6
AREA AREA AREA AREA HAZARD HAZARD HAZARD HAZARD SAFEGUARDS SAFEGUARDS SAFEGUARDS SAFEGUARDS
Tells where Tells where Tells where Tells where Tells what the hazard is. Tells what the hazard is. Tells what the hazard is. Tells what the hazard is. Tells how to avoid the hazard. Tells how to avoid the hazard. Tells how to avoid the hazard. Tells how to avoid the hazard.
hazards may occur. hazards may occur. hazards may occur. hazards may occur.
Spray Area Spray Area Spray Area Spray Area Fire Hazard Fire Hazard Fire Hazard Fire Hazard Fire extinguishing equipment must be present in the Fire extinguishing equipment must be present in the Fire extinguishing equipment must be present in the Fire extinguishing equipment must be present in the
spray area and tested periodically. spray area and tested periodically. spray area and tested periodically. spray area and tested periodically.
Improper or inadequate operation Improper or inadequate operation Improper or inadequate operation Improper or inadequate operation
and maintenance procedures will and maintenance procedures will and maintenance procedures will and maintenance procedures will Spray areas must be kept clean to prevent the Spray areas must be kept clean to prevent the Spray areas must be kept clean to prevent the Spray areas must be kept clean to prevent the
cause a fire hazard. cause a fire hazard. cause a fire hazard. cause a fire hazard. accumulation of combustible residues. accumulation of combustible residues. accumulation of combustible residues. accumulation of combustible residues.
Protection against inadvertent Protection against inadvertent Protection against inadvertent Protection against inadvertent Smoking must never be allowed in the spray area. Smoking must never be allowed in the spray area. Smoking must never be allowed in the spray area. Smoking must never be allowed in the spray area.
arcing that is capable of causing arcing that is capable of causing arcing that is capable of causing arcing that is capable of causing
fire or explosion is lost if any safety fire or explosion is lost if any safety fire or explosion is lost if any safety fire or explosion is lost if any safety The high voltage supplied to the atomizer must be The high voltage supplied to the atomizer must be The high voltage supplied to the atomizer must be The high voltage supplied to the atomizer must be
interlocks are disabled during interlocks are disabled during interlocks are disabled during interlocks are disabled during turned off prior to cleaning, flushing, or maintenance. turned off prior to cleaning, flushing, or maintenance. turned off prior to cleaning, flushing, or maintenance. turned off prior to cleaning, flushing, or maintenance.
operation. Frequent power supply operation. Frequent power supply operation. Frequent power supply operation. Frequent power supply
shutdown indicates a problem in shutdown indicates a problem in shutdown indicates a problem in shutdown indicates a problem in When using solvents for cleaning: When using solvents for cleaning: When using solvents for cleaning: When using solvents for cleaning:
the system requiring correction. the system requiring correction. the system requiring correction. the system requiring correction.
Those used for equipment flushing should have flash Those used for equipment flushing should have flash Those used for equipment flushing should have flash Those used for equipment flushing should have flash
points equal to or higher than those of the coating points equal to or higher than those of the coating points equal to or higher than those of the coating points equal to or higher than those of the coating
material. material. material. material.
Those used for general cleaning must have flash Those used for general cleaning must have flash Those used for general cleaning must have flash Those used for general cleaning must have flash
points at least 5 points at least 5 points at least 5 points at least 5°C (9 C (9 C (9 C (9° F.) above ambient tempera- F.) above ambient tempera- F.) above ambient tempera- F.) above ambient tempera-
ture. It is the end users responsibility to insure this ture. It is the end users responsibility to insure this ture. It is the end users responsibility to insure this ture. It is the end users responsibility to insure this
condition is met.
condition is met. condition is met. condition is met.
Spray booth ventilation must be kept at the rates Spray booth ventilation must be kept at the rates Spray booth ventilation must be kept at the rates Spray booth ventilation must be kept at the rates
required by local codes and national codes. In required by local codes and national codes. In required by local codes and national codes. In required by local codes and national codes. In
addition, ventilation must be maintained during addition, ventilation must be maintained during addition, ventilation must be maintained during addition, ventilation must be maintained during
cleaning operations using flammable or combustible cleaning operations using flammable or combustible cleaning operations using flammable or combustible cleaning operations using flammable or combustible
solvents. solvents. solvents. solvents.
Electrostatic arcing must be prevented. Electrostatic arcing must be prevented. Electrostatic arcing must be prevented. Electrostatic arcing must be prevented.
Test only in areas free of combustible material. Test only in areas free of combustible material. Test only in areas free of combustible material. Test only in areas free of combustible material.
Testing may require high voltage to be on, but only as Testing may require high voltage to be on, but only as Testing may require high voltage to be on, but only as Testing may require high voltage to be on, but only as
instructed. instructed. instructed. instructed.
Non Non Non Non----factory replacement parts or unauthorized factory replacement parts or unauthorized factory replacement parts or unauthorized factory replacement parts or unauthorized
equipment modifications may cause fire or injury. equipment modifications may cause fire or injury. equipment modifications may cause fire or injury. equipment modifications may cause fire or injury.
If used, the key switch bypass is intended for use only If used, the key switch bypass is intended for use only If used, the key switch bypass is intended for use only If used, the key switch bypass is intended for use only
during setup operations. Production should never be during setup operations. Production should never be during setup operations. Production should never be during setup operations. Production should never be
done with safety interlocks disabled. done with safety interlocks disabled. done with safety interlocks disabled. done with safety interlocks disabled.
Never use equipment intended for use in waterborne Never use equipment intended for use in waterborne Never use equipment intended for use in waterborne Never use equipment intended for use in waterborne
installations to spray solvent based materials. installations to spray solvent based materials. installations to spray solvent based materials. installations to spray solvent based materials.
The paint process and equipment should be set up The paint process and equipment should be set up The paint process and equipment should be set up The paint process and equipment should be set up
and operated in accordance with NFPA and operated in accordance with NFPA and operated in accordance with NFPA and operated in accordance with NFPA----33, NEC, and 33, NEC, and 33, NEC, and 33, NEC, and
EN Health and Safety requirements. EN Health and Safety requirements. EN Health and Safety requirements. EN Health and Safety requirements.
SAFETY PRECAUTIONS SAFETY PRECAUTIONS SAFETY PRECAUTIONS SAFETY PRECAUTIONS