Ransburg No. 2 Air Motor Atex Approved Unit 80086-XX - Manual (Page 5)

5 5 5 5 AH AH AH AH----12 12 12 12----01.03 No. 2 Air Motor Handgun 01.03 No. 2 Air Motor Handgun 01.03 No. 2 Air Motor Handgun 01.03 No. 2 Air Motor Handgun
AREA AREA AREA AREA HAZARD HAZARD HAZARD HAZARD SAFEGUARDS SAFEGUARDS SAFEGUARDS SAFEGUARDS
Tells where hazards Tells where hazards Tells where hazards Tells where hazards Tells what the hazard is. Tells what the hazard is. Tells what the hazard is. Tells what the hazard is. Tells how to avoid the hazard. Tells how to avoid the hazard. Tells how to avoid the hazard. Tells how to avoid the hazard.
may occur. may occur. may occur. may occur.
Spray Area Spray Area Spray Area Spray Area Electrostatic Arcing Electrostatic Arcing Electrostatic Arcing Electrostatic Arcing Never operate the spray gun without properly Never operate the spray gun without properly Never operate the spray gun without properly Never operate the spray gun without properly
grounding the following. grounding the following. grounding the following. grounding the following.
A. Operators A. Operators A. Operators A. Operators
Operators must be grounded. Rubber soled Operators must be grounded. Rubber soled Operators must be grounded. Rubber soled Operators must be grounded. Rubber soled
insulating shoes should not be worn. insulating shoes should not be worn. insulating shoes should not be worn. insulating shoes should not be worn.
Grounding leg straps may be used. Grounding leg straps may be used. Grounding leg straps may be used. Grounding leg straps may be used.
Operators must maintain contact with the Operators must maintain contact with the Operators must maintain contact with the Operators must maintain contact with the
handle of the gun. If work gloves are used, the handle of the gun. If work gloves are used, the handle of the gun. If work gloves are used, the handle of the gun. If work gloves are used, the
palm section should be cut out. palm section should be cut out. palm section should be cut out. palm section should be cut out.
Operators must remove from themselves all Operators must remove from themselves all Operators must remove from themselves all Operators must remove from themselves all
metal objects that are not grounded. metal objects that are not grounded. metal objects that are not grounded. metal objects that are not grounded.
NOTE: REFER TO NFPA
NOTE: REFER TO NFPA NOTE: REFER TO NFPA NOTE: REFER TO NFPA----33/EN 50 176 RE- 33/EN 50 176 RE- 33/EN 50 176 RE- 33/EN 50 176 RE-
GARDING OPERATOR GROUNDING. GARDING OPERATOR GROUNDING. GARDING OPERATOR GROUNDING. GARDING OPERATOR GROUNDING.
B. Parts being sprayed. Resistance between the B. Parts being sprayed. Resistance between the B. Parts being sprayed. Resistance between the B. Parts being sprayed. Resistance between the
part and a grounded conveyor must not exceed part and a grounded conveyor must not exceed part and a grounded conveyor must not exceed part and a grounded conveyor must not exceed
1 megohm. 1 megohm. 1 megohm. 1 megohm.
C. Every metal and conductive object in the spray C. Every metal and conductive object in the spray C. Every metal and conductive object in the spray C. Every metal and conductive object in the spray
area. This includes the booth, parts hangers, area. This includes the booth, parts hangers, area. This includes the booth, parts hangers, area. This includes the booth, parts hangers,
fire extinguishers, conductive flooring, etc. fire extinguishers, conductive flooring, etc. fire extinguishers, conductive flooring, etc. fire extinguishers, conductive flooring, etc.
Grounded conductive flooring must be provided in Grounded conductive flooring must be provided in Grounded conductive flooring must be provided in Grounded conductive flooring must be provided in
the spray area. the spray area. the spray area. the spray area.
Turn off voltage at the power supply before flushing Turn off voltage at the power supply before flushing Turn off voltage at the power supply before flushing Turn off voltage at the power supply before flushing
out, cleaning, or removing any parts from the gun. out, cleaning, or removing any parts from the gun. out, cleaning, or removing any parts from the gun. out, cleaning, or removing any parts from the gun.
Provide proper protection for waterborne supply Provide proper protection for waterborne supply Provide proper protection for waterborne supply Provide proper protection for waterborne supply
systems. systems. systems. systems.
Never install a spray gun into a fluid system using an Never install a spray gun into a fluid system using an Never install a spray gun into a fluid system using an Never install a spray gun into a fluid system using an
isolated solvent supply. isolated solvent supply. isolated solvent supply. isolated solvent supply.
Always discharge Waterborne system capacitance Always discharge Waterborne system capacitance Always discharge Waterborne system capacitance Always discharge Waterborne system capacitance
prior to servicing. prior to servicing. prior to servicing. prior to servicing.
Do not touch gun electrode while gun is energized. Do not touch gun electrode while gun is energized. Do not touch gun electrode while gun is energized. Do not touch gun electrode while gun is energized.
SAFETY PRECAUTIONS SAFETY PRECAUTIONS SAFETY PRECAUTIONS SAFETY PRECAUTIONS