Ransburg No. 2 Air Motor Atex Approved Unit 80086-XX - Manual (Page 32)

AH AH AH AH----12 12 12 12----01.03 No. 2 Air Motor Handgun 01.03 No. 2 Air Motor Handgun 01.03 No. 2 Air Motor Handgun 01.03 No. 2 Air Motor Handgun 32 32 32 32
REPAIR PROCEDURES REPAIR PROCEDURES REPAIR PROCEDURES REPAIR PROCEDURES
Read each procedure entirely before begin- Read each procedure entirely before begin- Read each procedure entirely before begin- Read each procedure entirely before begin-
ning.
ning. ning. ning.
NOTE NOTE NOTE NOTE
High voltage components, such as cable and High voltage components, such as cable and High voltage components, such as cable and High voltage components, such as cable and
high voltage resistor, are not field serviceable.
high voltage resistor, are not field serviceable. high voltage resistor, are not field serviceable. high voltage resistor, are not field serviceable.
For repair or replacement of such items, contact
For repair or replacement of such items, contact For repair or replacement of such items, contact For repair or replacement of such items, contact
your Ransburg distributor.
your Ransburg distributor. your Ransburg distributor. your Ransburg distributor.
Tools Required Tools Required Tools Required Tools Required
14.5 mm 9/16 14.5 mm 9/16 14.5 mm 9/16 14.5 mm 9/16----inch Open End Wrench inch Open End Wrench inch Open End Wrench inch Open End Wrench
5/8 5/8 5/8 5/8----inch Open End Wrench inch Open End Wrench inch Open End Wrench inch Open End Wrench
3/4 3/4 3/4 3/4----inch Open End Wrench inch Open End Wrench inch Open End Wrench inch Open End Wrench
3.5 mm or 9/64 3.5 mm or 9/64 3.5 mm or 9/64 3.5 mm or 9/64----inch Hex Wrench inch Hex Wrench inch Hex Wrench inch Hex Wrench
6 inch Adjustable Wrench 6 inch Adjustable Wrench 6 inch Adjustable Wrench 6 inch Adjustable Wrench
1/4 1/4 1/4 1/4----inch Open End Wrench (Ignition inch Open End Wrench (Ignition inch Open End Wrench (Ignition inch Open End Wrench (Ignition
Type) Type) Type) Type)
Bench Vise, Flat Jawed Bench Vise, Flat Jawed Bench Vise, Flat Jawed Bench Vise, Flat Jawed
Spare Parts Kit (9096 Spare Parts Kit (9096 Spare Parts Kit (9096 Spare Parts Kit (9096----00) 00) 00) 00)
Pliers Pliers Pliers Pliers
Screwdriver (short and long shaft) Screwdriver (short and long shaft) Screwdriver (short and long shaft) Screwdriver (short and long shaft)
3mm (1/8 3mm (1/8 3mm (1/8 3mm (1/8----inch) Straight Punch inch) Straight Punch inch) Straight Punch inch) Straight Punch
8 mm (5/16 8 mm (5/16 8 mm (5/16 8 mm (5/16----inch) Drill Bit inch) Drill Bit inch) Drill Bit inch) Drill Bit
Preliminary Disassembly Preliminary Disassembly Preliminary Disassembly Preliminary Disassembly
Prior to performing any service on the gun the Prior to performing any service on the gun the Prior to performing any service on the gun the Prior to performing any service on the gun the
following procedures should be followed:
following procedures should be followed: following procedures should be followed: following procedures should be followed:
1. Turn the high voltage “OFF” and disconnect 1. Turn the high voltage “OFF” and disconnect 1. Turn the high voltage “OFF” and disconnect 1. Turn the high voltage “OFF” and disconnect
the AC power to the power supply.
the AC power to the power supply. the AC power to the power supply. the AC power to the power supply.
W A R N I N G W A R N I N G W A R N I N G W A R N I N G
BEFORE attempting any cleaning or BEFORE attempting any cleaning or BEFORE attempting any cleaning or BEFORE attempting any cleaning or
color change procedures the high voltage color change procedures the high voltage color change procedures the high voltage color change procedures the high voltage
and the AC power to the power supply
and the AC power to the power supply and the AC power to the power supply and the AC power to the power supply
MUST be turned OFF! MUST be turned OFF! MUST be turned OFF! MUST be turned OFF!
2. Flush the fluid line and gun with a suitable 2. Flush the fluid line and gun with a suitable 2. Flush the fluid line and gun with a suitable 2. Flush the fluid line and gun with a suitable
solvent.
solvent. solvent. solvent.
3. Loosen the set screw on the bell hub, re- 3. Loosen the set screw on the bell hub, re- 3. Loosen the set screw on the bell hub, re- 3. Loosen the set screw on the bell hub, re-
move and clean the bell. Refer to "Effects of
move and clean the bell. Refer to "Effects of move and clean the bell. Refer to "Effects of move and clean the bell. Refer to "Effects of
Solvents" in the "Maintenance" section for a
Solvents" in the "Maintenance" section for a Solvents" in the "Maintenance" section for a Solvents" in the "Maintenance" section for a
list of cleaning solvents.
list of cleaning solvents. list of cleaning solvents. list of cleaning solvents.
4. Turn fluid pressure OFF. Bleed all pressure 4. Turn fluid pressure OFF. Bleed all pressure 4. Turn fluid pressure OFF. Bleed all pressure 4. Turn fluid pressure OFF. Bleed all pressure
from the line.
from the line. from the line. from the line.
5. Disconnect the fluid at the rear of the gun. 5. Disconnect the fluid at the rear of the gun. 5. Disconnect the fluid at the rear of the gun. 5. Disconnect the fluid at the rear of the gun.
6. Disconnect the high voltage cable from the 6. Disconnect the high voltage cable from the 6. Disconnect the high voltage cable from the 6. Disconnect the high voltage cable from the
power supply.
power supply. power supply. power supply.
Filter Cleaning or Replacement Filter Cleaning or Replacement Filter Cleaning or Replacement Filter Cleaning or Replacement
(Refer to Figure 17) (Refer to Figure 17) (Refer to Figure 17) (Refer to Figure 17)
Disconnect the fluid hose assembly from the Disconnect the fluid hose assembly from the Disconnect the fluid hose assembly from the Disconnect the fluid hose assembly from the
filter assembly . Hold the filter assembly rear
filter assembly . Hold the filter assembly rear filter assembly . Hold the filter assembly rear filter assembly . Hold the filter assembly rear
housing with a 3/4
housing with a 3/4 housing with a 3/4 housing with a 3/4----inch open end wrench and inch open end wrench and inch open end wrench and inch open end wrench and
with a 5/8 with a 5/8 with a 5/8 with a 5/8----inch open end wrench turn the fluid inch open end wrench turn the fluid inch open end wrench turn the fluid inch open end wrench turn the fluid
hose nut in a clockwise direction (left hand hose nut in a clockwise direction (left hand hose nut in a clockwise direction (left hand hose nut in a clockwise direction (left hand
threads) to remove the fluid hose.
threads) to remove the fluid hose. threads) to remove the fluid hose. threads) to remove the fluid hose.
Disconnect the filter assembly from the gun Disconnect the filter assembly from the gun Disconnect the filter assembly from the gun Disconnect the filter assembly from the gun
assembly. Secure the hose connector assem-
assembly. Secure the hose connector assem- assembly. Secure the hose connector assem- assembly. Secure the hose connector assem-
bly with a 5/8
bly with a 5/8 bly with a 5/8 bly with a 5/8----inch open end wrench and with inch open end wrench and with inch open end wrench and with inch open end wrench and with
a 3/4 a 3/4 a 3/4 a 3/4----inch open end wrench connected to the inch open end wrench connected to the inch open end wrench connected to the inch open end wrench connected to the
filter assembly nut , turn the nut clockwise and filter assembly nut , turn the nut clockwise and filter assembly nut , turn the nut clockwise and filter assembly nut , turn the nut clockwise and
remove the filter assembly.
remove the filter assembly. remove the filter assembly. remove the filter assembly.
MAINTENANCE MAINTENANCE MAINTENANCE MAINTENANCE