Ransburg No. 2 Air Motor Atex Approved Unit 80086-XX - Manual (Page 40)

AH AH AH AH----12 12 12 12----01.03 No. 2 Air Motor Handgun 01.03 No. 2 Air Motor Handgun 01.03 No. 2 Air Motor Handgun 01.03 No. 2 Air Motor Handgun 40 40 40 40
BARREL ASSEMBLY BARREL ASSEMBLY BARREL ASSEMBLY BARREL ASSEMBLY
High Voltage Resistor High Voltage Resistor High Voltage Resistor High Voltage Resistor Replacement Replacement Replacement Replacement
(Refer to Figure 24) (Refer to Figure 24) (Refer to Figure 24) (Refer to Figure 24)
1. Remove the cable/motor assembly per 1. Remove the cable/motor assembly per 1. Remove the cable/motor assembly per 1. Remove the cable/motor assembly per
steps 1 and 2 of "Cable Assembly Replace-
steps 1 and 2 of "Cable Assembly Replace- steps 1 and 2 of "Cable Assembly Replace- steps 1 and 2 of "Cable Assembly Replace-
ment" in the "Maintenance" section. Remove
ment" in the "Maintenance" section. Remove ment" in the "Maintenance" section. Remove ment" in the "Maintenance" section. Remove
the brush (Item 1) from the resistor housing
the brush (Item 1) from the resistor housing the brush (Item 1) from the resistor housing the brush (Item 1) from the resistor housing
(Item 5).
(Item 5). (Item 5). (Item 5).
2. Insert a long shaft standard screwdriver 2. Insert a long shaft standard screwdriver 2. Insert a long shaft standard screwdriver 2. Insert a long shaft standard screwdriver
into the lower opening at the rear of the bar- into the lower opening at the rear of the bar- into the lower opening at the rear of the bar- into the lower opening at the rear of the bar-
rel assembly and remove screw (Item 8) and
rel assembly and remove screw (Item 8) and rel assembly and remove screw (Item 8) and rel assembly and remove screw (Item 8) and
washer (Item 7).
washer (Item 7). washer (Item 7). washer (Item 7).
ITEM ITEM ITEM ITEM DESCRIPTION DESCRIPTION DESCRIPTION DESCRIPTION ITEM ITEM ITEM ITEM DESCRIPTION DESCRIPTION DESCRIPTION DESCRIPTION
1 1 1 1 80085 80085 80085 80085----00 Brush 00 Brush 00 Brush 00 Brush 5 5 5 5 Resistor Housing Resistor Housing Resistor Housing Resistor Housing
2 2 2 2 O O O O----Ring Ring Ring Ring 6 6 6 6 Barrel Barrel Barrel Barrel
3 3 3 3 Resistor Seal Resistor Seal Resistor Seal Resistor Seal 7 7 7 7 Washer Washer Washer Washer
4 4 4 4 HV Resistor 525 M HV Resistor 525 M HV Resistor 525 M HV Resistor 525 MΩ Ω Ω Ω 8 8 8 8 Screw Screw Screw Screw
Figure 24: HV Resistor Removal Figure 24: HV Resistor Removal Figure 24: HV Resistor Removal Figure 24: HV Resistor Removal
C A U T I O N C A U T I O N C A U T I O N C A U T I O N
Resistor is made of ceramic material. Resistor Resistor is made of ceramic material. Resistor Resistor is made of ceramic material. Resistor Resistor is made of ceramic material. Resistor
will break if dropped, mishandled, or exposed to
will break if dropped, mishandled, or exposed to will break if dropped, mishandled, or exposed to will break if dropped, mishandled, or exposed to
solvents.
solvents. solvents. solvents.
3. Cover the front of the barrel (Item 6) with a 3. Cover the front of the barrel (Item 6) with a 3. Cover the front of the barrel (Item 6) with a 3. Cover the front of the barrel (Item 6) with a
rag. With an air gun (set at a maximum of 3
rag. With an air gun (set at a maximum of 3 rag. With an air gun (set at a maximum of 3 rag. With an air gun (set at a maximum of 3
bar/50 psig) at the rear of the resistor housing,
bar/50 psig) at the rear of the resistor housing, bar/50 psig) at the rear of the resistor housing, bar/50 psig) at the rear of the resistor housing,
blow the resistor seal (Item 3), o
blow the resistor seal (Item 3), o blow the resistor seal (Item 3), o blow the resistor seal (Item 3), o----ring (Item 2), ring (Item 2), ring (Item 2), ring (Item 2),
and resistor (Item 4) out the front of the barrel. and resistor (Item 4) out the front of the barrel. and resistor (Item 4) out the front of the barrel. and resistor (Item 4) out the front of the barrel.
4 Clean the resistor housing (Item 5) with a
4 Clean the resistor housing (Item 5) with a 4 Clean the resistor housing (Item 5) with a 4 Clean the resistor housing (Item 5) with a
nonconductive solvent and dry thoroughly.
nonconductive solvent and dry thoroughly. nonconductive solvent and dry thoroughly. nonconductive solvent and dry thoroughly.
(Refer to "Effects of Solvents" in the
(Refer to "Effects of Solvents" in the (Refer to "Effects of Solvents" in the (Refer to "Effects of Solvents" in the
"Maintenance" section.) Inspect the ID of
"Maintenance" section.) Inspect the ID of "Maintenance" section.) Inspect the ID of "Maintenance" section.) Inspect the ID of
each end of the resistor tube for any signs of
each end of the resistor tube for any signs of each end of the resistor tube for any signs of each end of the resistor tube for any signs of
high voltage tracking or arcing.
high voltage tracking or arcing. high voltage tracking or arcing. high voltage tracking or arcing.
NOTE NOTE NOTE NOTE
If resistor is not pushed out by the air, If resistor is not pushed out by the air, If resistor is not pushed out by the air, If resistor is not pushed out by the air, insert a insert a insert a insert a
rigid wire into the rear of the resistor housing rigid wire into the rear of the resistor housing rigid wire into the rear of the resistor housing rigid wire into the rear of the resistor housing
and push the resistor out. Be careful not to
and push the resistor out. Be careful not to and push the resistor out. Be careful not to and push the resistor out. Be careful not to
scratch or scar the inside of resistor housing.
scratch or scar the inside of resistor housing. scratch or scar the inside of resistor housing. scratch or scar the inside of resistor housing.